T O P I C R E V I E W
|
mrsmcizzle
Member # 9643
|
posted
I have a stock '86 gt roller shortblock and sum gt40 heads that were ported with stock springs and no lifters. My question is whats a good cam under .500 lift that would allow me to keep my stock springs and still give me good performance? Any and all advice is much needed.
|
FivePTSlow
Member # 7682
|
posted
quote: Originally posted by mrsmcizzle: I have a stock '86 gt roller shortblock and sum gt40 heads that were ported with stock springs and no lifters. My question is whats a good cam under .500 lift that would allow me to keep my stock springs and still give me good performance? Any and all advice is much needed.
Mostly anyone is going to recommend new springs with any cam above stock. Even switching to 1.7 ratio roller rocker arms typically should have upgraded springs and that only adds roughly .03" of lift to your cam. Plus consider how many miles are on your springs already. They might even need to be replaced with the use of the factory cam.
As for cams, I've only had a few cams. I've had the stock cam with factory rocker arms, & 1.7 roller rockers, Ford B-Cam, Ford F-Cam, & a Crane Nostalgia Cam. So far I like the F-Cam the best. It's power band is a little higher than stock or b-cam which helps a little bit with traction, but once you're in the power band it pulls hard. B-Cam I actually liked as an overall cam and might be a good way to go for what you're looking at. .480/.480 lift with more duration than the stock cam and it has a decently broad power curve.
|
turbo50
Member # 6700
|
posted
I'll have one ground for you that's low lift split pattern with a tad more duration and on a 111 works pretty good with gt40s as does b and f cam if ur springs are up to par
|
warhorse58gt
Member # 7702
|
posted
What is the pvc with those stock flat tops?
|
wilit
Member # 3367
|
posted
quote: Originally posted by warhorse58gt: What is the pvc with those stock flat tops?
+1. I didn't think you could run non E6 heads and a higher than stock lift cam with the '86 flat tops.
|
turbo50
Member # 6700
|
posted
I'll fly cut for you for a small fee if its out of the car. I've had good luck with my little custom cam and up to 1.90/1.6 valves but every motor is different.
|
mrsmcizzle
Member # 9643
|
posted
quote: Originally posted by turbo50: I'll have one ground for you that's low lift split pattern with a tad more duration and on a 111 works pretty good with gt40s as does b and f cam if ur springs are up to par
The block isnt in the car and my heads arent on the block. Let me kno whats my bill
|
mrsmcizzle
Member # 9643
|
posted
Alot of folks are sayin just run with 1.7 rockers it'll do me better justice since i have the stock flat top pistons if thats the case, what size rods do i get?
|
turbo50
Member # 6700
|
posted
quote: Originally posted by mrsmcizzle: Alot of folks are sayin just run with 1.7 rockers it'll do me better justice since i have the stock flat top pistons if thats the case, what size rods do i get?
This is the route I'd go and you'll be fine with the stock 6.250 pushrods I'm sure.
|
mrsmcizzle
Member # 9643
|
posted
What size studs am i supposed to get anybody know?
|
JohnB
Member # 969
|
posted
quote: Originally posted by mrsmcizzle: What size studs am i supposed to get anybody know?
Is Dan doing your setup? If so, I'm sure he knows.
|
mrsmcizzle
Member # 9643
|
posted
Naw im doin this myself i rather have Dan do my stroker
|