T O P I C R E V I E W
|
mike g
Member # 2919
|
posted
Just wondering if any of you are running this? Had any problems using it?
mike
|
sharkattack
Member # 645
|
posted
quote: Originally posted by mike g: Just wondering if any of you are running this? Had any problems using it?
mike
I have it minus the windage tray. Nice piece.
|
BOUNTY HUNTER VERT
Member # 2754
|
posted
It is a waste of $$$$ the block is still gonna break
|
LAST302
Member # 808
|
posted
quote: Originally posted by BOUNTY HUNTER VERT: It is a waste of $$$$ the block is still gonna break
I disagree. I have both pieces and they are nice. Logically when bolted up and you look at it, it must add some strength due to the bolting pattern and the way it is set in. Just my opinion.
|
mike g
Member # 2919
|
posted
so with the main support and windage tray was there any machining recquired or clearance problems?
mike
|
LAST302
Member # 808
|
posted
I had to bend the oil sump bracket around the main support with my hands and that is it. There pieces work very nicely together and they give VERY GOOD directions as opposed to some of the others out there. They explain how to do this procedure also. [ September 04, 2003, 11:45 AM: Message edited by: LAST302 ]
|
BOUNTY HUNTER VERT
Member # 2754
|
posted
Lol i had a main support from chp and all it did was keep my parts in a nice pile when the block split mind you at only 512 rwhp on 12 psi
|
big matt
Member # 1124
|
posted
quote: Originally posted by LAST302: I had to bend the oil sump bracket around the main support with my hands and that is it. There pieces work very nicely together and they give VERY GOOD directions as opposed to some of the others out there. They explain how to do this procedure also.
i had to do the same thing
|
LAST302
Member # 808
|
posted
quote: Originally posted by BOUNTY HUNTER VERT: Lol i had a main support from chp and all it did was keep my parts in a nice pile when the block split mind you at only 512 rwhp on 12 psi
Dont blame the girdle on that one bud!!!
|
sharkattack
Member # 645
|
posted
quote: Originally posted by big matt: quote: Originally posted by LAST302: I had to bend the oil sump bracket around the main support with my hands and that is it. There pieces work very nicely together and they give VERY GOOD directions as opposed to some of the others out there. They explain how to do this procedure also.
i had to do the same thing
I didn't but I have a front sump pan with pick up for my 65. Everything fit great. [ September 05, 2003, 06:29 AM: Message edited by: sharkattack ]
|
93PONY
Member # 60
|
posted
Aluminum should not be used as a girdle on Iron caps. Aluminum expands at just about twice the rate of iron. This means as your motor is warming up the girdle is expanding faster....actually pushing on the caps. Steel is a MUCH better choice for a girdle.
FYI, when ANY girdle is installed the mains should be line-honed with the girdle torqued in place.
IMO, all a girdle will do is keep the busted parts in a nice pile when the block breaks. If you're running over 500RWHP, or over 450RW but turning the motor over 6500rpm you should really think about getting a stronger block. If you're not making that kind of power, the stock block is fine....but there's no real need for a girdle....with the possible exception of a 350+RWHP motor that is shifted over 6500rpm & has the occassion bottle run through it.
|
sharkattack
Member # 645
|
posted
quote: Originally posted by 93PONY: Aluminum should not be used as a girdle on Iron caps. Aluminum expands at just about twice the rate of iron. This means as your motor is warming up the girdle is expanding faster....actually pushing on the caps. Steel is a MUCH better choice for a girdle.
FYI, when ANY girdle is installed the mains should be line-honed with the girdle torqued in place.
IMO, all a girdle will do is keep the busted parts in a nice pile when the block breaks. If you're running over 500RWHP, or over 450RW but turning the motor over 6500rpm you should really think about getting a stronger block. If you're not making that kind of power, the stock block is fine....but there's no real need for a girdle....with the possible exception of a 350+RWHP motor that is shifted over 6500rpm & has the occassion bottle run through it.
Thats my set up.
|
stoauto
Member # 2803
|
posted
quote: Originally posted by BOUNTY HUNTER VERT: Lol i had a main support from chp and all it did was keep my parts in a nice pile when the block split mind you at only 512 rwhp on 12 psi
ONLY 512 rwhp, on a stock block?? thats a given. c'mon now.
|
stoauto
Member # 2803
|
posted
atleast we know that aluminum dampens harmonics better.
|