|
Author
|
Topic: SOLD-1988 Ford Mustang Coupe (Notch Back) Road Race Drift Car
|
Casey90GT
¯
Member # 6175
|
posted
 
***CAR IS SOLD-THANKS CAFords!!!***
Well, the Mustang is finally done! And that means it's time to list it for sale. This car just passed Smog with flying colors, and has had a professional alignment since the installation of all the new suspension goodies. 90% of the parts on this car are brand new, and have only been once around my block to make sure everything works, and then back and forth to the Smog shop and alignment place.
Starting with a basic '88 Notch, I stripped the car to the bare tub, scrubbed and painted the entire underside of the vehicle, repairing minor cracks in the floor pan, welding seems, etc. Then I built the car, essentially from the ground up with the following parts.
Chassis and Suspension:
Maximum Motorsports Full Length Subframe Connectors
UPR Upper and Lower Torque Box Reinforcing "Battle Box" Kit
Maximum Motorsports Six Point Roll Cage
Maximum Motorsports K-Member Brace
Maximum Motorsports Strut Tower Bar
Maximum Motorsports Caster/Camber Plates
2003 SVT Cobra Control arms with Urethane Bushings
Flaming River Quick Ratio Power Rack & Pinion
Maximum Motorsports Aluminum Rack Bushings
Maximum Motorsports Collapsible Steering Shaft
Maximum Motorsports SN95 Bump Steer Kit
Koni Yellow Adjustable Struts
Maximum Motorsports Front Coilovers w/500lb Springs
Stock 4-Cylinder Front Swaybar w/ Urethane Bushings & Links
Racecraft SN95 Dropped Spindles
New OEM SN95 Hubs
Baer Brakes 13" Front C6 Corvette Brake Kit
Stainless Steel Front Brake Lines
Koni Yellow Adjustable Shocks
Maximum Motorsports Rear Coilovers w/ 375lb Springs
Stock GT Rear Swaybar
Maximum Motorsports Heavy Duty Rear Lower Control Arms
Edelbrock Adjustable Rear Upper Control Arms
Maximum Motorsports Panhard Bar
Eaton Brute Force 31-Spline Clutch Type Posi Unit
Tom's Kick Ass Fox Length 31-Spline Axles
Trick Flow Rear End Girdle
Baer Brakes 12.65" Rear C5 Corvette Brake Kit
Stainless Steel Rear Brake Lines
Power Train:
90,000 mile '95 Shortblock with ported E7's
Crane Compucam 2040 Cam & Lifters (Same as E Cam)
Edelbrock Performer EFI Intake Manifold
Edelbrock 70mm Throttle Body & Spacer
Holley Adjustable Fuel Pressure Regulator
C&L 73mm Mass Air Meter
24-lb Cobra (Thin Body) Fuel Injectors
MSD 6AL Box, Blaster TFI Coil, Cap, Rotor, and Plug Wires
MAC Ceramic Coated Headers
Ford Racing Underdrive Pulleys
3G Alternator Upgrade w/ 2-Gauge Power Wire
Stock 4-Cat H-Pipe (for SMOG)
Spintech Catback Exhaust (Sounds Wicked)
Summit Racing Aluminum Radiator
Ford Racing Silicone Hose Kit
Custom Wired Taurus Fan with Integral Controller
Trick Flow A/C Eliminator
Prothane Urethane Motor Mounts
Stock T5 Transmission
Centerforce Dual Friction Clutch
Steeda Firewall Adjuster, Double Hook Quadrant, and Adjustable Cable
Hurst Shifter
Prothane Urethane Transmission Mount
Ford Racing Aluminum Driveshaft
Interior:
Custom Upholstered Recaro SE Seats
Stroud 5-Point Harnesses
Grant GT Wheel w/ Quick Disconnect
Hurst Chrome Tall Shifter Handle w/ White Hurst Ball
Autometer Phantom 5" Tach w/ ShiftLight
New Black Carpet Kit
Stock Rear Seat (but good luck getting in it)
All interior panels and stock rear seat were carefully fitted around rollcage
Rolling Stock:
18x9" FR500 Wheels; Black w/ Polished Lip
P245/40ZR18 Sumitomo HTRZII's
Less than 100 miles on the set.
Misc:
Trunk Mounted Battery
Fuel Pump Shutoff switch
Baer Brakes Master Cylinder, Booster, and Adjustable Proportioning Valve
The Bad:
(1)The body isn't perfect; there are some dings, a couple of small dents, and the paint is slightly off-shade on one of the doors and both bumpers (I swapped these parts because they were in better shape than the ones that were on the car and I was planning on going to Maaco). I still might paint the car if it doesn't sell right away.
(2)The gauges in the stock instrument cluster don't all work (I am trying to fix this right now).
Anyway, I'm sure I've forgotten some things, but that get's you the basic idea. This car is ready to go out and dominate the road course, or drift around your favorite canyon. You will not find a more well-sorted, expertly assembled fox body for any price. I have worked in racing and high performance shops in the past, and have over 10 years of professional mechanical experience. I was building this car with the intention of keeping it, so you can be sure that it was built right. I even have a fastener checklist with torque values that I used when I went through the car on assembly. It is SOLID!
I'm asking $10,000 obo for this car, because that is what I have wrapped up in just suspension, steering, brakes, and chassis stiffening. Basically you buy all of that and the rest of the car is free!
Feel free to email me with any questions!
Thanks,
Casey Hudson
cjhudson87@msn.com
[ July 09, 2010, 03:38 PM: Message edited by: Casey90GT ]
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
STANGBOY
¯
Member # 7868
|
posted
anytrades for an 86 coupe
[ May 06, 2010, 06:01 PM: Message edited by: STANGBOY ]
--------------------
1986 mustang notchback
she's good from far but far from good
Posts: 2510 | From: SAN JOSE | Registered: Aug 2007
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
See list of potential trades below. Thanks!
[ June 19, 2010, 03:29 PM: Message edited by: Casey90GT ]
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
73 on DUBS
Car thief associate!
Member # 5677
|
posted
PICS PLEASE SOUNDS LIKE A BAD ASS COUPE
--------------------
you r not ready!!!! -H$$-
###################################
Juan Moralas aka Julienn Morales aka 73 on DUBS accompliced by his brother Ben Moralas aka Benjamin Moralas aka bnmrls aka benmorales94025@yahoo.com of Menlo Park (408)431-3020 / (650)271-2509 pictured here is a member of the East Palo Alto car theft ring called High Speed Specialist aka HSS aka H$$ which has loose Norteño gang ties. Be suspect of Ben Morales / Juan Morales and their EPA criminal H$$ affiliates. They've been spotted at various car shows, 7th street, and Sacramento Raceway.
This thief affiliated High Speed Specialists group is **NOT** related to the legit drag racing group under the same name out of Oakland.
###################################
STOLEN Mustang SALEEN FOUND AT "73 ON DUBS" FAMILY'S HOUSE
Known Car Thieves: BEWARE
###################################
Posts: 672 | From: da LO | Registered: May 2005
| :
|
|
CHP2981
¯
Member # 9240
|
posted
Hey Casey what's up so your almost done huh just paint it and drive it. I think the best way to advertise is to drive it. Usually when you don't want to sell it and just driving around is when people ask about it. Good luck
Posts: 521 | From: Richmond | Registered: Jun 2009
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
BTT...
PLEASE!!!
Read my ad before emailing me. Don't waste my time and I won't waste yours. I just exchanged SEVERAL emails with two different members, both of which didn't see my $10k asking price. I might be willing to negotiate my price, but this is not a $3,500 notch...so don't waste my time if you aren't on the level.
PS-I have a hood, and a few moldings still left to install on the car. More exterior shots to follow, but whoever buys this car isn't going to buy it for the exterior anyway.
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
RODRIGUEZ
¯
Member # 9104
|
posted
TTT for a bad ass coupe.
If I was you I would just paint it and keep it dude.
I'm sure you put in ALOT of hours of you're life that you will never get back building this coupe.
And also, it would be a bitch to have to do it all over again.
Posts: 1182 | From: East Bay | Registered: Apr 2009
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
BTT
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
KRZ89GT
¯
Member # 4273
|
posted
bad ass road racer! ![[patriot]](graemlins/patriot.gif)
--------------------
89' bLACk GT (stolen)
KRAZYFORDS
Posts: 353 | From: MICHOACAN | Registered: Mar 2004
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
Somebody by this car before I get arrested for driving like an asshole!!! I don't mean to hijack my own post, but I don't think I'm mature enough to own a car like this! ![[burnout]](graemlins/burnout.gif)
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
Jaejae5.0
¯
Member # 7958
|
posted
this car is dope...if you dont sell it just put jaejae in your will ![[Whoo Whooooo!]](graemlins/woowoo.gif) ..goodluck with sale..amazing car
--------------------
1987 notchback h/c/i 302 & 70mm turbo SOLD
2000 camaro ss cam only
Posts: 4890 | From: the combustion chamber | Registered: Oct 2007
| :
|
|
50 Deep
Jockin 03 Cobras
Member # 6216
|
posted
I got a 61 jaguar xk9 for ya.....
Sick car though. Love to swap in a 03/04 drivetrain and kill the track
--------------------
Signature Wheel Ford Representative
Email: Terrance@Signaturewheel.com
Instagram: @Signature_Wheel_Mustang
Web: www.SignatureWheel.com
Posts: 6043 | From: sacramento | Registered: Nov 2005
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
Hey...email me pics and details on that Jag. My email address is cjhudson87@msn.com if you're serious.
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
Just FYI; I will consider partial to full trades for some classic cars, E36 BMW m3's, late 90's to early 2000's Porsche Boxsters, C5 Corvettes, etc. I will consider a VERY partial trade (like up to $3,000 off my price) for a good condition, lower mileage Nissan or Toyota 2WD pickup truck.
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
welch93lx
¯
Member # 8748
|
posted
trade for a 1998 BMW 740IL BLACK ON BLACK??
Posts: 705 | From: modesto | Registered: Nov 2008
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
quote:
Originally posted by welch93lx:
trade for a 1998 BMW 740IL BLACK ON BLACK??
PM sent!
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
As I said before, I am open to offers...and suggestions. I am thinking of going the eBay route. Has anybody ever tried that, and how much success did you have with it?
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
ponystroker
¯
Member # 7635
|
posted
i have if your interested an ls2 1993 rx7. but you would have to put some cash on top..let me know.
Posts: 74 | From: 510 | Registered: May 2007
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
That sounds like a sick car, but I don't really have any extra $$$.
TTT!!!
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
|
|
Casey90GT
¯
Member # 6175
|
posted
Just posted up on Corral...I'm gonna give the car one week there, and then I think I'm gonna do an eBay listing (I will set a reserve $1,000-2,000 below my current asking price). I'd really like to see the car stay in Northern California, so if you think you want it make me an offer. Me and my buddy have been working on a fun video of what this beast is capable of too...I'll have that on YouTube as soon as it's all edited together (can you say 70mph power-slide!?!). Also got the hood painted and installed. Here's a pic!!!
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
TTT...no reasonable offer refused!
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
coupedup
¯
Member # 9987
|
posted
That's a clean look'n notch man ! I had an 87ssp with a built 347/novi2000 and a 10pt cage , corbeau racing seats , saleen/racecraft suspension , subframe cnnecters , tremecTKO 600 , alum driveshaft , m&m torque arm , panhard bar and tons and tons of other mods . The thing is to remember with these cars n actually not just mustangs but all cars is that no matter how hard you try you'll never get back what you put in to it when trying to sell . I know it sucks but that's just the way it is . N believe me , I took a serious hit on selling that mustang but needed the dough n had to take a loss on it . But anyhow , very nice car bro n GLWS !!!
Posts: 4406 | From: Ca | Registered: May 2010
| :
|
|
Casey90GT
¯
Member # 6175
|
posted
Thanks for the compliments, and kind words. It sounds like your car was insanely cool. I can't imagine this thing with a blower.
The bottom line is, I am taking a tremendous hit at $10k, but I'm willing to go even lower than that if somebody brings a serious cash offer to the table. That being said though, I've sold quite a few fox bodies over the years, and I know roughly what a modded car of this caliber is worth, so I think that my expectations are pretty much in line with the price I'm gonna end up sellin this thing for.
--------------------
Some day I'll finish it.
Posts: 1064 | From: Santa Rosa | Registered: Nov 2005
| :
|
|
coupedup
¯
Member # 9987
|
posted
Yea , I hear ya . I also have owned/sold more foxbody's than I care to remember and I know what kind of values they carry aswell . My point was that it's gonna be hard period to even get close as to what you may have into it .
Posts: 4406 | From: Ca | Registered: May 2010
| :
|
|
Topic Closed
Printer friendly view of this Ford topic
