|
Author
|
Topic: NEED HELP!!a.s.a.p!!!!!!!!Revs real HIgh at 2500
|
Eddie510-
CAFords OG
Member # 2354
|
posted
 
 
ok, I start The car,than after i take out the clutch, it over revs at around 2500 rpms!!!WHY is that??Than if you put the clutch in, it idels NOrmal??what the hell is that???i asked ford and they said they diddnt know??it a 90gt, (when i put the tranny in i diddnt use the reinlinement tool ![[Frown]](frown.gif) could that be a problem??it gets into gears fine but it Whines like a superCharger??when i had this t5 in my other stang it never did that wining noise???Thanks eddie ![[patriot]](graemlins/patriot.gif)
--------------------
"I like to be more politicaly correct than what I really believe so I can get more frinds here on CaFords"-Cummings "TIPICKLE"
Posts: 6556 | Registered: Jan 2003
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
The alignment tool is only needed to help align the splines on the trany to mate with the clutch plate splines...
Did you add enough trans fluid?...You know your supposed to use AutoTransFluid, right?..
Is your vehicle speed sensor hooked up?...its the sensor on the top of the trany...
If that is all good, I would try running the codes with a code scanner...
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
Eddie510-
CAFords OG
Member # 2354
|
posted
ummm,when i installed the tranny i dumped the old tranny fluid and put some new, but kragen told me to use 80-90 gear oil so i put that, but than i dumped it out and put atf Fluid? did i mess the tranny up by putting that gear oil???
--------------------
"I like to be more politicaly correct than what I really believe so I can get more frinds here on CaFords"-Cummings "TIPICKLE"
Posts: 6556 | Registered: Jan 2003
| :
|
|
Eddie510-
CAFords OG
Member # 2354
|
posted
my speed sensor is not hooked up cuase i broke but i put the peace of the speedsensor into the tranny but i diddnt tightn it all the way cuz it wont let me
--------------------
"I like to be more politicaly correct than what I really believe so I can get more frinds here on CaFords"-Cummings "TIPICKLE"
Posts: 6556 | Registered: Jan 2003
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
It would've been smart to flush out the old 70w90 with ATF...as long as you have enough ATF you should be fine...Take out the check fill plug on the top passenger side of the trany and let any extra fluid drain out...Make sure that the fluid level atleast comes up to the bottom of the check fill plug hole...
[ October 13, 2003, 07:25 PM: Message edited by: Black94 5.0 ]
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
Eddie510-
CAFords OG
Member # 2354
|
posted
quote:
I would try running the codes with a code scanner... [/QB]
Where can i get that at and what does that do, thanks eddie
--------------------
"I like to be more politicaly correct than what I really believe so I can get more frinds here on CaFords"-Cummings "TIPICKLE"
Posts: 6556 | Registered: Jan 2003
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
quote:
Originally posted by Eddie510:
my speed sensor is not hooked up cuase i broke but i put the peace of the speedsensor into the tranny but i diddnt tightn it all the way cuz it wont let me
The computer needs input from the vehicle speed sensor...You might wanna fix that first!...
You could buy a code scanner, but it would be pointless if you already know that the VSS is broken...
[ October 13, 2003, 07:29 PM: Message edited by: Black94 5.0 ]
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
Eddie510-
CAFords OG
Member # 2354
|
posted
lol,k thanks for ya help
--------------------
"I like to be more politicaly correct than what I really believe so I can get more frinds here on CaFords"-Cummings "TIPICKLE"
Posts: 6556 | Registered: Jan 2003
| :
|
|
Email this post to someone!
Printer friendly view of this Ford topic
