|
Author
|
Topic: help need more power!
|
siri95
CAFords OG
Member # 2840
|
posted
 
 
whats up everyone... okay im a new member here cause some guy came up to me and started to look at my car... man the power of stangs bringing mustang drivers together but when we are on the road.. its differnt.
anyways.... does anyone have any advise to gain more power for my 1995 5.0. the thing is i dont have that much money to spend so the cheepest way would be good for me.
--------------------
1995 Mustang GT (sold)
1992 Ford F-150 XLT (sold)
1986 Mustang SVO (sold)
Posts: 783 | From: 510 | Registered: May 2003
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
Whad up!...Welcome to californiafords.com!...
I think I was that guy that came up to you at Ohlone, right?....
Well like I was saying a set of gear is about $400 for parts and install....I recommend the Ford Motorsport gears($179)...You can expect around 3-4 tenths in the quarter with a jump from 2.73's(stock) to 3.73's....Rear end specialties in Santa Clara are pretty good to have install them...
Then I recommend under drive pullies...I put ASP pullies on my car and I think it was the best bang for buck that I put on the car..They are around $90 and worth about 15-18 hp..(7-10rwhp)
Finally with the Flowmasters installed I got an "off-road H-pipe" for my B-day...I gained 3 tenths in the quarter mile with the "off-road H pipe"...
That should get you started...Dont forget the first mod everyone does and should do, and thats a K&N air filter ![[Wink]](wink.gif) ...
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
RTornio
¯
Member # 2289
|
posted
Buy a chevy? hehe.. just fuckin with ya... But seriously, id agree with the previous... underdrive pulleys help out alot, and getting rid of the chain of cats on the mustangs helps alot too. A cold air intake and exhaust would help too, if you dont already have it... once you have the basic bolt ons down... we can move on to better things, such as gears, nitrous, sticky tires and good clutch Since you ford boys dont seem to have issues with your rears, you can run sticky tires with no problems....
--------------------
Current Rides:
2014 Lexus IS250 FSport
2007 Toyota Tundra SR5 5.7 TRD 4x4
2010 Toyota Sienna Limited
1988 Ford Mustang GT 306ci
Posts: 220 | From: Fremont, Ca | Registered: Jan 2003
| :
|
|
KCmustangboy
¯
Member # 1927
|
posted
quote:
Originally posted by RTCamaroSS:
Buy a chevy? hehe.. just fuckin with ya... But seriously, id agree with the previous... underdrive pulleys help out alot, and getting rid of the chain of cats on the mustangs helps alot too. A cold air intake and exhaust would help too, if you dont already have it... once you have the basic bolt ons down... we can move on to better things, such as gears, nitrous, sticky tires and good clutch Since you ford boys dont seem to have issues with your rears, you can run sticky tires with no problems....
Well when your rearend isn't made buy chevy it lasts a lot longer.... ![[Big Grin]](biggrin.gif) ![[burnout]](graemlins/burnout.gif) sorry had to say it ![[patriot]](graemlins/patriot.gif)
--------------------
03 Cobra... Factory long block, with Whipple and AED tune... 812rwhp 10.0s @ 140... almost there!
WWW.AEDHP.COM
Posts: 1691 | From: San Jose, CA | Registered: Oct 2002
| :
|
|
RTornio
¯
Member # 2289
|
posted
Hehehe, no complaints here... ill be ordering my 9 inch soon...
--------------------
Current Rides:
2014 Lexus IS250 FSport
2007 Toyota Tundra SR5 5.7 TRD 4x4
2010 Toyota Sienna Limited
1988 Ford Mustang GT 306ci
Posts: 220 | From: Fremont, Ca | Registered: Jan 2003
| :
|
|
siri95
CAFords OG
Member # 2840
|
posted
right on guys. yeah i am the guy from Ohlone. parking away from all the other cars.. cause i dont want my stang to get dinged....okay.. im gonna be really real here.. these terms sounds hella cool and this is my first car i ever bought with my own money...my last car was a 1986 subrua xt...so it came a big jump.... but can u explain what pulleys do and where it goes..and this "cat" thing.. i bet i sound like a fool but hey. im a new stang owner. so can u guys do me a favor... im soo but damn. im tryin my hardest here... o yeah another thing..aye black5.0 guy..thanks man. for letting me know about this site.
--------------------
1995 Mustang GT (sold)
1992 Ford F-150 XLT (sold)
1986 Mustang SVO (sold)
Posts: 783 | From: 510 | Registered: May 2003
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
Yeah, when I drive my Stang I ALWAYS park in a corner spot....
Underdrive pulley's replace the stock pulley's on the front of the engine...You normally buy the kits with 3 pulley's.(the alternator, water pump and crank).....Basically by increasing or decreasing certain pulley's on an engine, it makes it eaiser to turn those certain pulley's...So, by making it easier to turn the pulley's on your engine, you gain/free up horse power....
Catylitic converters(cats) on a car can restrict your exhaust flow out of the engine....Getting rid of the cats you will get an increase in flow, giving you more horse power...
Changing the gears on a Mustang or any car is like changing the gears on your 21 speed mountain bike...The lower ones make it easy to accelerate but you have a lower top speed....Unfortunately the stock gears on a Mustang are designed more for gas miledge than performance...
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
siri95
CAFords OG
Member # 2840
|
posted
right on! yeah.. shit ever since i got the stang.. i see all these new marks.. im thinking its the rocks that my car picks up.. or other shit on the road..okay..really though i am thinking about putting these pulleys on.also im thinking about putting them "off-road flows"? off road... maybe its some term.. well first that intake then flows... o yeah if i were just to put flows and intake how much u think i would be pulling.? cause i kinda wanna stay close to stock. but have more power. i want that feel where my car is pushing me right in my seat and im sorry.. its not..kinda want alittle more pull...and black945.0 how much did u get ur tints for your stang.? are u gonna be on campus tomorrow.?
--------------------
1995 Mustang GT (sold)
1992 Ford F-150 XLT (sold)
1986 Mustang SVO (sold)
Posts: 783 | From: 510 | Registered: May 2003
| :
|
|
Hungry Hippo
¯
Member # 537
|
posted
i have a mac cold air kit for 94/95's if you're interested
--------------------
05 S4 Avant(wagon)
09 C6 H/C/I
Posts: 2959 | From: east bay | Registered: Nov 2001
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
Sorry My last final was on Monday, so I wont be at class...
Its not "off-road flows"...Flowmasters and an off-road pipe are different....Buy a 2.5" Flowmaster cat back, meaning from your "cat"-ylitic h pipe to the back of the car(tips)....An off road H-pipe is called "off road" becuase its illegal to drive a car on the road without "cats"...
I suggest going to the store and buying a Mustang mag, like "Muscle Mustangs & Fast Fords" or "5.0 and Super Fords"....
My window tint was done by Rocky Mountain Window Tint in Fremont...
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
siri95
CAFords OG
Member # 2840
|
posted
cool. how much are you planing to dump the cold air kit for..?o yea another thing
since i just got this 1995 gt. im hearing clicking sounds in my engine.. like it clicks witht the rmp's....if the rpm's are low the "clicks" are slow..and if i rev it the clicks get faster....
man i have problems allready... does anyone know whats goiing on..
anyways...i hope u did good on ur final. ill prob see you around.are u planing to go to the show at cal state hayward.?welll u think its a good idea if i were to get this clod kit?
--------------------
1995 Mustang GT (sold)
1992 Ford F-150 XLT (sold)
1986 Mustang SVO (sold)
Posts: 783 | From: 510 | Registered: May 2003
| :
|
|
Glenn
¯
Member # 520
|
posted
quote:
Originally posted by siri95:
cool. how much are you planing to dump the cold air kit for..?o yea another thing
since i just got this 1995 gt. im hearing clicking sounds in my engine.. like it clicks witht the rmp's....if the rpm's are low the "clicks" are slow..and if i rev it the clicks get faster....
man i have problems allready... does anyone know whats goiing on..
anyways...i hope u did good on ur final. ill prob see you around.are u planing to go to the show at cal state hayward.?welll u think its a good idea if i were to get this clod kit?
That sounds like an exhaust leak.
--------------------
S-Trim,331,H/C/I
"JohnB groupie train"
My Car
DragGuam
Posts: 2009 | From: Stationed on a Pacific Island, Guam | Registered: Oct 2001
| :
|
|
Jdub07
( O Y O )
Member # 2728
|
posted
what kind of gas are you using? I always use 91 nothing less. is it a ping noise or ticking noise? If its a ping noise then I would look into adjusting your timing and fuel octane. If its a ticking then yeah it sounds like an exhaust leak. I know a lot about exhaust leaks just don't know as much about fixing it :-)
I am so new to mustangs too so what I have been doing is popin my hood alot getting familiar with the car. Do work on your own whenever possible....even crawl under and around it to check out all the things people are talking about on the board. Thats just what helps me.
Also your lucky to have met black 94 5.0 I always take his advise and wouldn't do anything to my car that he wouldn't do to his. He never tells me what I should or shouldn't do, he just says what "he" would do and that works for me.
I have learned a ton of information from the board, I don't post as much but read a lot. And yeah get a couple mustang magazines, go to some of the boards cruzes and shows too. Welcome to the board.
Posts: 7282 | Registered: Apr 2003
| :
|
|
siri95
CAFords OG
Member # 2840
|
posted
damn...its like this...right when i start my engine.. alittle after. clicking starts to occur...?and when i apply gas the clicking gets faster...? any adivse.?
and how to fix it.. and is it.. bad for my eingine.?
thanks
--------------------
1995 Mustang GT (sold)
1992 Ford F-150 XLT (sold)
1986 Mustang SVO (sold)
Posts: 783 | From: 510 | Registered: May 2003
| :
|
|
siri95
CAFords OG
Member # 2840
|
posted
well. i just posted a reply but you bet me to it...the sound in my eninge sounds more like.. ticking..then pining...and the gas i use is 91 Chevron with Techron...man that sounds cool. when i say that... i heard that if i were to get 76... my engine's performance would inprove..is that correct.?well i think ill still stick with chevron...
im glad i met black945.0 cause if i wouldnt. i would notknow nothing about my mustang. i am learning so much in here and its soo helpful.
anyways.. is this leak bad?
--------------------
1995 Mustang GT (sold)
1992 Ford F-150 XLT (sold)
1986 Mustang SVO (sold)
Posts: 783 | From: 510 | Registered: May 2003
| :
|
|
Glenn
¯
Member # 520
|
posted
you are losing a little HP if it is an exhaust leak. If you wanna come buy my palce I can tell you if it is an exhaust leak. I am in san leandro.
--------------------
S-Trim,331,H/C/I
"JohnB groupie train"
My Car
DragGuam
Posts: 2009 | From: Stationed on a Pacific Island, Guam | Registered: Oct 2001
| :
|
|
Jdub07
( O Y O )
Member # 2728
|
posted
yeah it can't be good for the car, how long have you owned it, have you done an oil, fuel, fuel filter and spark change. sounds dumb but my car will tick some when the oil is low. wanna hear something else dumb.......i've had about 9 cars since I was 17 (26 now) and just the other day I learned that the oil gauge in the car is oil "pressure" not "level". No wonder I went through so many cars!!
Posts: 7282 | Registered: Apr 2003
| :
|
|
Jdub07
( O Y O )
Member # 2728
|
posted
in my opinion your safe with 76 or chevron. I don't get gas anywhere but cheveron, I used to be stuck on 76 but one of the pumps ripped me off one day so whatever.
ticking is better than pinging but still not good. it could be from a number of places but shouldn't be to difficult to locate or fix. I had a bad exhaust leak when I installed my off road h pipe. took me some time but I finally got the kinks out. I ended up replacing a couple other parts such as o2 sensors, and header gaskets just to be on the safe side.
Totally off the subject but how hard is it to get fourth gear scratch...?
Posts: 7282 | Registered: Apr 2003
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
Hey thanx for the props guys!....
Siri95~~~Sounds just like an exhaust leak...You could take it to an exhaust shop and get it fixed or you could do it yourself.....If you take it to an exhuast shop I'd make sure they know about Mustangs...Apex in Santa Clara, I'm sure could fix the leak no problem....
If you do it yourself you need to know where the leak is comming from....Pop the hood and see if you can pin point where its comming from....Its most likely comming from the header gasket...You might be able to feel a little air comming out in between the engine and the header flange where the leak is...Do you have stock headers?....You can replace the header gasket with a better gasket (like Felpro) and re-seal the header so it doenst leak...You might also want to check and make sure that the bolts from your H-pipe to your headers are tight...
Good luck!
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
quote:
Originally posted by Jdub07:
Totally off the subject but how hard is it to get fourth gear scratch...?
Its easy, I can show you!
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
Jdub07
( O Y O )
Member # 2728
|
posted
quote:
Originally posted by Black94 5.0:
quote:
Originally posted by Jdub07:
Totally off the subject but how hard is it to get fourth gear scratch...?
Its easy, I can show you!
When are we gonna run!?
Posts: 7282 | Registered: Apr 2003
| :
|
|
siri95
CAFords OG
Member # 2840
|
posted
sounds good. since i live in union city and u live not that far from me.. i really dont mind if u check it out.? just give me a time and day and ill see if i can.. go. i need all the help i can get.
i just bought this car.and its not even been a month yet. and right now my pockets have no grenn any where..
o yeah i wouldnt know if its hard to get into fourth without any troulbe.. i havent pushed my car yet to its limit. one day i will..
but man.. hows everyones gas miles..? cause shi*t i get about 170 a full tank and i push it to the empty line.? the guy who i bought it from said that my car is running "rich". and i have a gauge on my engine. he said its the fuel pump gauge so im thinking thats the reason why? but i dont really know.?
--------------------
1995 Mustang GT (sold)
1992 Ford F-150 XLT (sold)
1986 Mustang SVO (sold)
Posts: 783 | From: 510 | Registered: May 2003
| :
|
|
Synergy Motorsports
New Member
Member # 2846
|
posted
If it is an exhaust leak, then the bad part would be determined by where the leak is. If it is before your O2 sensor, then that is bad because you are either getting outside air, or your O2 is not reading all it should. If after the O2, its still bad because when you lift, then colder air could come back in, but its not as bad. Either way you should get it fixed. Plus hey just sound bad and are annoying.
--------------------
Synergy Motorsports
For all your mustang, Camaro/Firebird and corvette Needs. Located in San Jose.
408-592-0404
Posts: 4 | From: Union City | Registered: May 2003
| :
|
|
BlackNGold
CaliforniaFords.com
Moderator
Member # 655
|
posted
quote:
Originally posted by Jdub07:
[
When are we gonna run!? [/QB][/QUOTE]
Come over tomm and we can cruise, and if your still interested we can race.....
--------------------
-SLOWER TRAFFIC KEEP RIGHT-
Posts: 5132 | From: Bay Area, CA | Registered: Dec 2001
| :
|
|
campindog
¯
Member # 1305
|
posted
1)Fix the exhaust leak. 2)Bump your timing to 14 degrees, but back off if it starts to ping under load. This is easy, free, and you'll feel the difference. 3)Get some gears. 4)If you have an AODE, get a shift kit.
Posts: 36 | From: San Jose | Registered: May 2002
| :
|
|
Email this post to someone!
Printer friendly view of this Ford topic
