|
Author
|
Topic: Anyone install TA/PHB
|
KeithStang7
¯
Member # 1945
|
posted
 
 
Has anyone ever installed their own torque arm or panhard bar? How long did it take? And do you have any tips for someone who has not done this before(me)? ![[patriot]](graemlins/patriot.gif)
--------------------
We the unwilling
Do the impossible
For the ungrateful
Posts: 393 | From: Redding, Ca | Registered: Oct 2002
| :
|
|
mtbaughs
Road Racer
Member # 4052
|
posted
What parts are you using? Griggs or maximum?
--------------------
R.I.P. Charlie Bruno Dec 2001
Posts: 2019 | From: Boise, Idaho | Registered: Jan 2004
| :
|
|
KeithStang7
¯
Member # 1945
|
posted
Maximum Motorsports
[ May 16, 2004, 10:07 PM: Message edited by: KeithStang7 ]
--------------------
We the unwilling
Do the impossible
For the ungrateful
Posts: 393 | From: Redding, Ca | Registered: Oct 2002
| :
|
|
mtbaughs
Road Racer
Member # 4052
|
posted
Well I've only been part of installing a few maximum kits as I like the quality of the Griggs products but theres a few tips to keep in mind when doing this job. Make sure you do use the plumb bobs to square the panhard bar in. Also any and all measurements they call for in the directions make sure you get right on the money and not just close. All the maximum panhard bars I've seen will not clear a T/A rear end cover so if you have that you might be getting rid of it for a stock cover. Many aftermarket tail pipes have real trouble clearing the maximum panhard bar and often you must cut and re-weld to clear the tires and bar. I would imagine a first timer to take about a day to install this stuff. You'll need a welder for the torque arm. Also you'll want different spring rates with the new set up front and rear. If theres any specific questions you have let me know
--------------------
R.I.P. Charlie Bruno Dec 2001
Posts: 2019 | From: Boise, Idaho | Registered: Jan 2004
| :
|
|
KeithStang7
¯
Member # 1945
|
posted
That sucks about the ta cover. They claim it will clear. I have access to a lift and air tools so the job won't be to grueling. Thanks for the tips.
--------------------
We the unwilling
Do the impossible
For the ungrateful
Posts: 393 | From: Redding, Ca | Registered: Oct 2002
| :
|
|
mtbaughs
Road Racer
Member # 4052
|
posted
Yeah the panhard bar I did didn't clear by a long shot even with the bearing supports cut flush with the jam nuts. I called them about this and they gave the typical ...Wow we've never seen that before. It all depends, they may have altered their design since the last one I did but you may want a stock cover nearby just in case. Make sure you check under the car in any case to make sure the bar isn't sitting on the T/A cover when the weight is on the wheels
--------------------
R.I.P. Charlie Bruno Dec 2001
Posts: 2019 | From: Boise, Idaho | Registered: Jan 2004
| :
|
|
NO MANRZ
¯
Member # 566
|
posted
I've got a friend with that setup and his clears the T/A... It might be close but it clears it. You guys must not follow the directions ![[Razz]](tongue.gif)
--------------------
Bring It . . .
Posts: 1938 | Registered: Nov 2001
| :
|
|
Blu50Stang
CAFords OG
Member # 489
|
posted
I just borrowed a friend's MM PHB to check the tailpipe clearance, and while it was close, it clears(1/2"). It also clears my T/A cover.
--------------------
Ross
'88 GT - 5.0&SF 4/04 | MM&FF 8/09 | MM&FF 79-93 Mustang Performance Cover 12/12
'17 GT350R
Posts: 1916 | From: Not CA | Registered: Oct 2001
| :
|
|
mtbaughs
Road Racer
Member # 4052
|
posted
ya I can't read the directions ![[Roll Eyes]](rolleyes.gif) Like I said it is a difference in MM's bar depending on when it was made or a variation in cars
Posts: 2019 | From: Boise, Idaho | Registered: Jan 2004
| :
|
|
Blu50Stang
CAFords OG
Member # 489
|
posted
quote:
Originally posted by mtbaughs:
ya I can't read the directions Like I said it is a difference in MM's bar depending on when it was made or a variation in cars
Ford's production tolerances also play a BIG role in whether or not you will have clearance issues.
--------------------
Ross
'88 GT - 5.0&SF 4/04 | MM&FF 8/09 | MM&FF 79-93 Mustang Performance Cover 12/12
'17 GT350R
Posts: 1916 | From: Not CA | Registered: Oct 2001
| :
|
|
NO MANRZ
¯
Member # 566
|
posted
quote:
Originally posted by mtbaughs:
ya I can't read the directions Like I said it is a difference in MM's bar depending on when it was made or a variation in cars
No harm done bud, just pulling your leg. The clearance we got on the car is right around 1-2mm so don't feel bad LOL
--------------------
Bring It . . .
Posts: 1938 | Registered: Nov 2001
| :
|
|
Johns331
New Member
Member # 4280
|
posted
I have a MM panhard bar on my TBird with a SVO girdle, and it fit fine. The TBird chassis is almost the same as a Mustang, especially in the rear axle area. I had to modify the left gas tank strap hanger for clearance and I'm going to have custom made tailpipes made up as there is just not enough room for any pre bent tail pipes.
--------------------
331 Powered TurboCoupe
Posts: 2 | From: Rosamond, Ca | Registered: Mar 2004
| :
|
|
KeithStang7
¯
Member # 1945
|
posted
Hey mtbaughs,
Would you be interested in helping me with this install? I want it to be done right. So if you've done it before then your a mile ahead of me. PM me with prices or requirements. Let me know if your up to it.
--------------------
We the unwilling
Do the impossible
For the ungrateful
Posts: 393 | From: Redding, Ca | Registered: Oct 2002
| :
|
|
Email this post to someone!
Printer friendly view of this Ford topic
