Author
|
Topic: Bleeding Brakes - 4.6L w/ ABS
|
90FoX
FoX
Member # 1974
|
posted
I wanted to know if there is any special procedure for bleeding brakes with ABS?
1) Do I just flush/bleed the brakes the same way as a car with no ABS?
2) I read in a few places that the 4.6L needs to have the Master Cylinder bled before bleeding the lines at the calipers. Is this true? If so can you elaborate on that?
3) If air gets into the abs system I wont be able to remove it myself at home right? So my question is if I have air in the brake lines right now, isn't there already air in the ABS module/control unit/system(whatever it's called, lol) already?
Thanks ![[patriot]](graemlins/patriot.gif) [ June 14, 2010, 07:39 AM: Message edited by: 90FoX ]
Posts: 5364 | From: Shooting Skeet | Registered: Oct 2002
| :
|
|
92stangLX
¯
Member # 3252
|
posted
I need to do this pretty soon too and am trying to do some research.
You should be able to bleed the same way as normal. If you let the MC run too low on fluid you may need to bleed it too (on the car). I ran into this issue with my 2001 GT.
If you find the procedure to bleed the MC please share
Posts: 5302 | From: San Francisco | Registered: Sep 2003
| :
|
|
Blind
2.3L CAFords OG
Member # 3052
|
posted
my `97 has bleed nipples on the M/C that I used to bleed it, I have a motive pressure bleeder that I use, just be careful not to get air into the ABS pump or it will have to be activated to get the air out - my buddy with an `03 cobra had that issue, it took forever to bleed out.
-------------------- 89 LX Notchback ex 4cyl, 14psi 02 Harley F150, 15psi
Posts: 8521 | From: Fairfield | Registered: Jul 2003
| :
|
|
92stangLX
¯
Member # 3252
|
posted
quote: Originally posted by Blind: my `97 has bleed nipples on the M/C that I used to bleed it, I have a motive pressure bleeder that I use, just be careful not to get air into the ABS pump or it will have to be activated to get the air out - my buddy with an `03 cobra had that issue, it took forever to bleed out.
what is the best procedure to bleed the MC without a pressure bleeder? Is it as simple as hooking rubber lines up to the nipples, feeding them into the top, and pump?
Posts: 5302 | From: San Francisco | Registered: Sep 2003
| :
|
|
Blind
2.3L CAFords OG
Member # 3052
|
posted
quote: Originally posted by 92stangLX: quote: Originally posted by Blind: my `97 has bleed nipples on the M/C that I used to bleed it, I have a motive pressure bleeder that I use, just be careful not to get air into the ABS pump or it will have to be activated to get the air out - my buddy with an `03 cobra had that issue, it took forever to bleed out.
what is the best procedure to bleed the MC without a pressure bleeder? Is it as simple as hooking rubber lines up to the nipples, feeding them into the top, and pump?
you got it, the one further away from the firewall I think is the rear port, do that one first, then the other, then bleed the rear brakes, then the fronts.
-------------------- 89 LX Notchback ex 4cyl, 14psi 02 Harley F150, 15psi
Posts: 8521 | From: Fairfield | Registered: Jul 2003
| :
|
|
90FoX
FoX
Member # 1974
|
posted
I see. So as long as I keep the fluid level high enough I shouldn't have to worry about bleeding the MC right?
I'm looking to pick up that motive pressure bleeder. I was researching it and it seem like an awesome tool.
btw is this the same motive pressure bleeder you have?
http://www.summitracing.com/parts/MVP-0107/ [ June 14, 2010, 03:05 PM: Message edited by: 90FoX ]
Posts: 5364 | From: Shooting Skeet | Registered: Oct 2002
| :
|
|
Blind
2.3L CAFords OG
Member # 3052
|
posted
quote: Originally posted by 90FoX: I see. So as long as I keep the fluid level high enough I shouldn't have to worry about bleeding the MC right?
I'm looking to pick up that motive pressure bleeder. I was researching it and it seem like an awesome tool.
btw is this the same motive pressure bleeder you have?
http://www.summitracing.com/parts/MVP-0107/
I got the "universal" kit they sell at amazon, it has a cap with a rubber cone in it and 2 J-hooks with chains that loop around the M/C, so it works in any M/C with a round cap.
I modded it for my fords by getting a ford cap and drilling then RTV'ing in a brass hose fitting through it, so for my fords I use that one which is easier because it just snaps on like the normal M/C cap.
only advice I can give with using it, is ALWAYS check for leaks with the bleeder EMPTY! If it leaks with brake fluid going through it, that shit sprays out everywhere @ 15psi and it's horrible on paint! I usually wrap the whole bleeder and M/C up with a towel just to be safe. I always hook it up empty, pump it to 15psi, let it sit for a couple minutes to make sure it holds, then fill it up and do the bleeding.
-------------------- 89 LX Notchback ex 4cyl, 14psi 02 Harley F150, 15psi
Posts: 8521 | From: Fairfield | Registered: Jul 2003
| :
|
|
92stangLX
¯
Member # 3252
|
posted
quote: Originally posted by Blind: quote: Originally posted by 92stangLX: quote: Originally posted by Blind: my `97 has bleed nipples on the M/C that I used to bleed it, I have a motive pressure bleeder that I use, just be careful not to get air into the ABS pump or it will have to be activated to get the air out - my buddy with an `03 cobra had that issue, it took forever to bleed out.
what is the best procedure to bleed the MC without a pressure bleeder? Is it as simple as hooking rubber lines up to the nipples, feeding them into the top, and pump?
you got it, the one further away from the firewall I think is the rear port, do that one first, then the other, then bleed the rear brakes, then the fronts.
Cool.. so one port on the MC at a time?
Posts: 5302 | From: San Francisco | Registered: Sep 2003
| :
|
|
BIGBALLFACTOR
¯
Member # 7277
|
posted
to beanch bleed a m/c the easy an the way i have done for the last 12 years put the master in vise fill with fluids stick fingers over the ports an push the cly in intill the bubbles are all gone install m/c hook up lines have some press the pedal down the crake the line open to get rid of the air in the lines
Posts: 6908 | From: okc | Registered: Dec 2006
| :
|
|
92stangLX
¯
Member # 3252
|
posted
quote: Originally posted by fasthatch: to beanch bleed a m/c the easy an the way i have done for the last 12 years put the master in vise fill with fluids stick fingers over the ports an push the cly in intill the bubbles are all gone install m/c hook up lines have some press the pedal down the crake the line open to get rid of the air in the lines
You can also do it on the car if you are not planning on changing the existing MC.
Posts: 5302 | From: San Francisco | Registered: Sep 2003
| :
|
|
BIGBALLFACTOR
¯
Member # 7277
|
posted
quote: Originally posted by 92stangLX: quote: Originally posted by fasthatch: to beanch bleed a m/c the easy an the way i have done for the last 12 years put the master in vise fill with fluids stick fingers over the ports an push the cly in intill the bubbles are all gone install m/c hook up lines have some press the pedal down the crake the line open to get rid of the air in the lines
You can also do it on the car if you are not planning on changing the existing MC.
NO SHIT REALLY NEVER KNEW THAT
Posts: 6908 | From: okc | Registered: Dec 2006
| :
|
|
90FoX
FoX
Member # 1974
|
posted
Can you tell me why there is a need to bleed the MC?
Where is air getting trapped? I figured as long as new fluid is pushed through the MC it will force air through the brake lines.
Another question I had was about bleeding the MC first. I thought you want to start furthest from the MC first then work your way towards it. So why do we bleed the MC first? Is it okay to bleed it again after all calipers are done to make sure all air is out?
Posts: 5364 | From: Shooting Skeet | Registered: Oct 2002
| :
|
|
BIGBALLFACTOR
¯
Member # 7277
|
posted
WHAT DID YOU DO TO THE BRAKE SYSTEM
Posts: 6908 | From: okc | Registered: Dec 2006
| :
|
|
90FoX
FoX
Member # 1974
|
posted
Im just trying to bleed it and get all air out of the system if any and get new fluid in the system. Who knows when someone changed the brake fluid last.
I know the procedure. Just confused about this whole MC thing. Doesn't make sense to me. Is there somewhere in the MC that air can be trapped even if you use a power bleeder to force new fluid through?
Posts: 5364 | From: Shooting Skeet | Registered: Oct 2002
| :
|
|
BIGBALLFACTOR
¯
Member # 7277
|
posted
quote: Originally posted by 90FoX: Im just trying to bleed it and get all air out of the system if any and get new fluid in the system. Who knows when someone changed the brake fluid last.
I know the procedure. Just confused about this whole MC thing. Doesn't make sense to me. Is there somewhere in the MC that air can be trapped even if you use a power bleeder to force new fluid through?
CLEAR YOUR PMS SO I CAN GIVE YE ANSWER
Posts: 6908 | From: okc | Registered: Dec 2006
| :
|
|
90FoX
FoX
Member # 1974
|
posted
Cleared
BTW I'm aware of the fact if air is in the abs system that Ill need a bi-directional ABS scan tool to operate the solenoids in order to fully purge air from the system.
But I don't think there is air in the ABS unless someone fucked up like an idiot. Lol [ June 17, 2010, 03:49 PM: Message edited by: 90FoX ]
Posts: 5364 | From: Shooting Skeet | Registered: Oct 2002
| :
|
|