|
Author
|
Topic: Need to know how to roll fenders
|
1sick65
¯
Member # 3957
|
posted
 
 
What has to be done to roll fenders for tire clearance? Thanks Nick
[ December 14, 2004, 04:27 PM: Message edited by: baggins ]
Posts: 1457 | From: Sacramento,CA | Registered: Jan 2004
| :
|
|
onesicklx
¯
Member # 285
|
posted
get a buddy and a wooden bat...put the bat between the fender and tire and have your buddy drive the car (slowly) forward and back...good luck
Posts: 1955 | From: san jose, CA | Registered: Jun 2001
| :
|
|
AJBlackGT
¯
Member # 3936
|
posted
Or you could buy the tool to to it right, Eastwood makes one and i think it costs around 200 bux. You should check out their website
--------------------
90 Notch
Posts: 1896 | From: Sacramento | Registered: Dec 2003
| :
|
|
SydeWaySix
CAFords OG
Member # 3596
|
posted
use a bat or an axehandle, don't drive the car though, just slowly bend the panel in.
be careful not to bend it too far and accidentally crack the paint
--------------------
2013 Boss 302 #356. Performance White. Stock.
1965 Fastback GT Restored to stock spec.
Posts: 9882 | From: Bay Area | Registered: Dec 2002
| :
|
|
mtbaughs
Road Racer
Member # 4052
|
posted
Make small cuts every half inch with a pancake cutter into the fender lip all the way around the fender. Cut until you reach an area that allows for the most clearance without being seen from the out board side of the fender. Than scribe a line through the paint just outside of your cut marks. This will keep the paint from flaking/cracking past your cut marks. Than take a hammer and flatten the cut portions one at a time until they are all folded up against the inside of the fender. Doing this will make certain you get the absolute most clearance without distorting the fender. For a finishing touch if you prefer a finished look bondo over the cut portion. You can use this method on the rear or in the front. If your doing the front than don't cut the portion of the fender lip that the fender liner mounts on. If theres no fender liner than cut all the way around as you did in the rear. Works like a charm everytime. Baseball bats can work though if you are not extremely careful you will distort the fender. You won't get as much clearance by simply bending the fender material up with this method. Good luck
Posts: 2019 | From: Boise, Idaho | Registered: Jan 2004
| :
|
|
NvrEnough89GT
¯
Member # 5086
|
posted
What is a pancake cutter? I need to do this as well to fit 18s and I like your idea. ![[patriot]](graemlins/patriot.gif)
--------------------
89 LX
Posts: 224 | From: Union City Ca | Registered: Dec 2004
| :
|
|
Eddie510-
CAFords OG
Member # 2354
|
posted
quote:
Originally posted by onesicklx:
get a buddy and a wooden bat...put the bat between the fender and tire and have your buddy drive the car (slowly) forward and back...good luck
ahahah.ghetto ![[Whoo Whooooo!]](graemlins/woowoo.gif) ![[worship]](graemlins/worship.gif) im hella laughing. thats hella crazy dude.
--------------------
"I like to be more politicaly correct than what I really believe so I can get more frinds here on CaFords"-Cummings "TIPICKLE"
Posts: 6557 | Registered: Jan 2003
| :
|
|
The Nick
¯
Member # 2244
|
posted
I used a bat too.
--------------------
Fast, Cheap or Reliable. Pick two and live with it.
Posts: 1215 | From: The Delta | Registered: Dec 2002
| :
|
|
mtbaughs
Road Racer
Member # 4052
|
posted
This without the shield installed
Posts: 2019 | From: Boise, Idaho | Registered: Jan 2004
| :
|
|
h8louzn
¯
Member # 1075
|
posted
I have used the bat and even used a maglight. Ghetto or not it works.
I will say that cutting is the best way by far!
[ December 17, 2004, 11:22 AM: Message edited by: h8louzn ]
Posts: 593 | From: Sac. | Registered: Mar 2002
| :
|
|
Gear Head
JARED
Member # 779
|
posted
quote:
Originally posted by mtbaughs:
This without the shield installed
Isn't that just a cut off wheel that can have the heads changed to sand, grind, ect.?
--------------------
Support our troops!
Posts: 5685 | From: EASTBAY | Registered: Jan 2002
| :
|
|
Gear Head
JARED
Member # 779
|
posted
quote:
Originally posted by mtbaughs:
Make small cuts every half inch with a pancake cutter into the fender lip all the way around the fender. Cut until you reach an area that allows for the most clearance without being seen from the out board side of the fender. Than scribe a line through the paint just outside of your cut marks. This will keep the paint from flaking/cracking past your cut marks. Than take a hammer and flatten the cut portions one at a time until they are all folded up against the inside of the fender. Doing this will make certain you get the absolute most clearance without distorting the fender. For a finishing touch if you prefer a finished look bondo over the cut portion. You can use this method on the rear or in the front. If your doing the front than don't cut the portion of the fender lip that the fender liner mounts on. If theres no fender liner than cut all the way around as you did in the rear. Works like a charm everytime. Baseball bats can work though if you are not extremely careful you will distort the fender. You won't get as much clearance by simply bending the fender material up with this method. Good luck
This is the best way to roll your fenders. I used tin snips instead of a pancake cutter.
--------------------
Support our troops!
Posts: 5685 | From: EASTBAY | Registered: Jan 2002
| :
|
|
Email this post to someone!
Printer friendly view of this Ford topic
