T O P I C R E V I E W
|
WeStBaY5.0
Member # 4736
|
posted
well as you can see the Pushrod bent and i cant pull it out! any sugg. on taking it out would be gratefull please LMK thanks
this is on my 89 f250 thanks once again
Danny
[ October 07, 2004, 04:04 PM: Message edited by: WeStBaY5.0 ]
|
Yellow94GT
Member # 431
|
posted
Um, replace the pushrod and go
|
WeStBaY5.0
Member # 4736
|
posted
thats the problem it wont come out!
|
66 AC COBRA
Member # 904
|
posted
but he says he cant pull it out, thats no good for a pushrod, why in the hell did it bend like that in the first place
looks like you need to take the intake off and make sure there isnt more dmage than you can see from there, or just to get a pair of pliers under there to pull that SOB out
|
Mr JoCo
Member # 1549
|
posted
screwdriver
|
WeStBaY5.0
Member # 4736
|
posted
Tried doing that alot, i dont think it will come out that easy...
|
HungryHippo
Member # 537
|
posted
vice grips and pull!
|
WeStBaY5.0
Member # 4736
|
posted
quote: Originally posted by Mr JoCo: screwdriver
can you be a little more specific thanks
|
WeStBaY5.0
Member # 4736
|
posted
quote: Originally posted by HungryHippo: vice grips and pull!
i have tried that a million times already that piece of sh*t wont come out!
|
Jdub07
Member # 2728
|
posted
wow! can they bend on the other end? if that end is that bad what can the other side look like. I wouldn't try and force it out not knowing what kind of damage might be learking on the other side. Pull off the head man.
Yet if you want to try and get it out can you bend it back at all? [ October 07, 2004, 04:10 PM: Message edited by: Jdub07 ]
|
WeStBaY5.0
Member # 4736
|
posted
i want to let that be the last option i dont think that damn pushrod will bend straight.!
yet this side is not affected, i can move it around i just cant pull it off? [ October 07, 2004, 04:13 PM: Message edited by: WeStBaY5.0 ]
|
Jdub07
Member # 2728
|
posted
quote: Originally posted by WeStBaY5.0: i want to let that be the last option i dont think that damn pushrod will bend straight.!
yet this side is not affected, i can move it around i just cant pull it off?
its already fucked off man...I'd bend it back strait or not your in need of new pushrods. Once you bend it back your chances of getting it out might be better. It look like since its "SO" bent the shaft of it (HAHAHA I SAID SHAFT) might be hung up on the inside of the hole. Just guessing...
I take no responsability in any action taken from any and/or all suggestions given by myself or given from my IP Address at any one given time or moment. [ October 07, 2004, 04:19 PM: Message edited by: Jdub07 ]
|
carajo
Member # 4426
|
posted
you HAVE to remove the intake, one,to see where its held/jammed at two,check lifter good luck.
|
stoauto
Member # 2803
|
posted
dude, just remove the damn intake. and be done with it. make sure when the intake is off theres no serious damage and check the lifter/lifters. how the hell did it bend like that anyway??
|
Mr JoCo
Member # 1549
|
posted
quote: Originally posted by WeStBaY5.0: quote: Originally posted by Mr JoCo: screwdriver
can you be a little more specific thanks
pry the fucker out
|
kwikrob
Member # 835
|
posted
pull the head, take it to a machine shop and have them check to see if anything else is screwed up. had to be a reason why it did that
|
Blowfish
Member # 4043
|
posted
I vote to pull the head off and cut one end of the rod off , then pound or pull it out. Damn nice mess. Good luck
|
WeStBaY5.0
Member # 4736
|
posted
well thanks guys for your support, i took the head off and im taking it to a shop to see if theres any damage done thanks again danny
|
BlownNOSMustang
Member # 158
|
posted
Remove upper and lower intake. Check all P-rods and replace broken one(s). Reasemble.
|