T O P I C R E V I E W
|
WantedCOBRA
Member # 3150
|
posted
1994 Cobra...
BBK Ceramic Coated Shorty Headers MAC Offroad H-Pipe Flow Master 3 Chamber Mufflers Edlebrock 70MM TB plus Spacer Cold Air Intake with K&N BBK Aluminum Underdrive Pullies
Stock Numbers HP = 240 @4800 Torque = 285 @ 4800
|
66 AC COBRA of CA PERFORMANCE
Member # 904
|
posted
dont forget the NX kit
|
Quick 88LX
Member # 1950
|
posted
I would say about 270hp max and about 300lb/ft max after those mods. They aren't that much so you can only get what you can. But don't take my word for it... See what these guys have to say
|
Luke87GT
Member # 21
|
posted
241 rear wheel hp is my guess... Luke
|
st5150
Member # 51
|
posted
254rwhp is my guess.
|
LAST302
Member # 808
|
posted
There is no spacer for a 94??
|
mustanggt5091
Member # 444
|
posted
265-275 hp and 295-305 tq
|
91sleeper
Member # 779
|
posted
260rwhp
|
94gt
Member # 3060
|
posted
how about for my 94gt? Also, will be putting on Flomaster 2 chambers with turndowns today! Thanks! [ September 08, 2003, 02:55 PM: Message edited by: 94gt ]
|
st5150
Member # 51
|
posted
quote: Originally posted by 94gt: how about for my 94gt? Also, will be putting on Flomaster 2 chambers with turndowns today! Thanks!
222rwhp
|
94gt
Member # 3060
|
posted
thanks man, god i want more rwhp.
|
WantedCOBRA
Member # 3150
|
posted
Any suggestions for more bolt-ons? I figure an Intake but that is 500 bones so is there anything cheaper than that I left out?
|
DropTopFox
Member # 1689
|
posted
Wanted CObra my guess is low only 230rwhp which comes to about 275 at the flywheel. As for recommended bolt ons looks like you have everything except a Mass air meter. That would go good with your bigger throttle body. Definately add some timing too. If you are looking for track times you are going to want some steeper gears in the rear end, my vote goes to 4.10's. Putting an alumnum driveshaft on is cheap and losing rotating weight will help accelleration in the quarter. Also a set of slicks would be a good idea. Looks like if you want more power though you are going to have to start thinking about a Heads, Cam and Intake combo
94GT my guess for you is 212rwhp. I try and guess low so that when you dyno you aren't dissappointed. Good Luck guys Ryan
|
94gt
Member # 3060
|
posted
damn! down and down it goes... lol
|
WantedCOBRA
Member # 3150
|
posted
So as far as Heads...would the Performer Intake work best with edlebrock heads? What does everyone think of AFR 165's? I dont know about a cam just yet becuase to me when you put a cam in your car you have graduated to pure strip. But thats just me...Also thanks to everyone for the input..it all helps...Gotta say WHAT UP to my homies in Fairfield, AC COBRA, 88 LX AND 5091!
|
Quick 88LX
Member # 1950
|
posted
An Edelbrock performer that is port matched to some 185's with some 1.6 roller rockers and your stock cam should be VERY nice. You can drive my car again if you wanna see what Edelbrock heads and intake matched up together feel like... But I vote 185 heads. And as for a cam, as long as your lift is below .550 you are looking at a VERY streetable car still. A pure strip cam is something like a solid roller or something like that. I must say that a cam is always a great addition to the modification family. I am looking to put one in before too long... Just haven't decided which one A cam will definitely help your car breath better hp numbers ![[Smile]](smile.gif) [ September 09, 2003, 03:42 PM: Message edited by: Quick 88LX ]
|
WantedCOBRA
Member # 3150
|
posted
It all sounds good...By the way this is my first post that has gotten to TWO PAGES.
|
94gt
Member # 3060
|
posted
|
DropTopFox
Member # 1689
|
posted
ANy time you ask a question like this that wil be argued over for days expect a lot of responses. It's like the occassional what combo should I go with. That thread can get up to 7 pages, I've seen it
|
DropTopFox
Member # 1689
|
posted
Oh and as for heads I highly reccommend the AFR 165's. Cam doesn't mean you're purely strip. I have an E-cam in my car and it may be bigger than stock but still a relatively small cam. In a post this weekend FastDamnit posted "Victor JR.'s, TW's, or 165's w/ a professional port job, RPM intake, and a cam with 224 duration and 540+ lift will take you into the 11's, and that is very streetable. I definately vote 165's on a 306, go 185's if you have a stroker
|
WantedCOBRA
Member # 3150
|
posted
Yeah thanks Droptop...I believe it is Muscle Mustang and Fast Fords that is testing different heads out as well as intakes. I believe it was the performer intake and the afr 165's or 185's that beat out all competition. The articles are long and very informative...for me anyway cuz I dont know shit...Thanks again...James
|