T O P I C R E V I E W
|
4.6GT
Member # 2643
|
posted
Where is a good place to install gears?how long does it take to do?thanx guys
|
Jdub07
Member # 2728
|
posted
rearend specialists took them about 2 hours to do mine.
|
Glenn
Member # 520
|
posted
where are you located?
|
4.6GT
Member # 2643
|
posted
Im in Vacaville but im willing to drive.I heard theres a place by the San Jose Airport.An whats the charge of the places
|
4.6GT
Member # 2643
|
posted
Where is rearend specialist at how much did they charge
|
chronicsmokin281
Member # 1649
|
posted
near apex motor sports! santa clara
|
4.6GT
Member # 2643
|
posted
How many car lenths difrence do gears make?
|
Cobra97
Member # 2809
|
posted
I called rearend specialties last week and they wanted $265 for the labor and gear oil. I am still trying to decide if I want to tackle this project myself.
|
JohnB
Member # 969
|
posted
If you're interested, I'm local and do them. (I'm out on Travis AFB) $150 plus supplies.
|
4.6GT
Member # 2643
|
posted
Jon B do you do a good job? what suplies will you need.what are the breaking in instructions
|
JohnB
Member # 969
|
posted
A "good" job? Actually, I think I do a great job Seriously though, I've done about 10 sets for people on the site, not to mention numerous sets of my own. (but I still got 93redcobra's to do..I haven't forgotten Sam!) Break in varies as to whether they are used or not. Brand new? Depends on the brands instruction, but as a general rule of thumb..about 50 miles of easy driving. Used? Beat the hell out of them when you leave my driveway. As long as they are setup correctly, they will last...new or used. If you're interested, lemme know.
Edit: supplies would be you'll need a install kit (or at least a new crush sleeve) and gear oil. [ August 12, 2003, 01:02 PM: Message edited by: JohnB ]
|
Glenn
Member # 520
|
posted
quote: Originally posted by JohnB: Used? Beat the hell out of them when you leave my driveway.
Hey don't forget the Base Police
|
cobraman_1994
Member # 467
|
posted
i think swason needs to make a sticky of this topic and a few others that i see every week
|
4.6GT
Member # 2643
|
posted
how much will the install kit cost me?Hoe much will suplies come out ? when do you have time to do that for me?
|
JohnB
Member # 969
|
posted
If you buy the COMPLETE install kit, it's about $95. What year is your 4.6? If it's a 96 or newer, and the seals are in good shape, all you really need is a new crush sleeve. Sleeve goes for about $10 or less, I haven't priced them out lately. Gear oil and friction modifier is about $25. As for when, when is the car available and you have the $$?
|
4.6GT
Member # 2643
|
posted
my car is 2002 gt with 27,000 miles am i going to need the install kit?
|
4.6GT
Member # 2643
|
posted
let me know where i can get all that stuff
|
5.0#4 87 T-Top GT
Member # 1534
|
posted
yea give rear end fuck ups (specialties) a call see how long your shit lasts....ha ha Don't go higher then 3.55 for a street car is my advice.
|
JohnB
Member # 969
|
posted
You don't need an install kit. A new crush sleeve can be picked up at any Napa parts store. The gear oil, etc can be bought there too. You need 3 qts of oil.
Only 3.55's? You must have 14" rims still. seriously though, if your wheel/tire combo warrants it, you can go as high as you want, as long as the combo is matched. Honestly, for a street car and a 5spd...I'd run 3.55's OR 3.73's..an auto? 4.10's are a MUST.
|
4.6GT
Member # 2643
|
posted
how are 3:73's on the freeway? so all you need is the ring and pinion gear,crush sleeve,and the oil and you could do it?
|
JohnB
Member # 969
|
posted
Really depends on what you are looking to get out of these gears. You race alot? Go w/ 3.73's...just want it to be a bit quicker? Go 3.55's. If it's a 5spd, you should have 3.27's already, so with 3.55's, you're not going to "feel" alot of difference.
Just depends on what you want. And yes, what you listed is all I need to do the job.
|
4.6GT
Member # 2643
|
posted
Im tryin to beat SS camaros cuz right they take me i have pro-chamber h-pipe,cold air,75mm throttle body and 2 chamber flows.im going to be getting steeda pullies,upper intake plenum ported and 3:73 gears do u think i can take a Ls1 SS maro thats what im trying to accomplish with those mods?do u think that will do it.
|