|
Author
|
Topic: shift kit and gears
|
slow&poor
¯
Member # 961
|
posted
 
 
I already have a trango shift kit in my car and I was wondering if I will have to modify it when I get gears put in.
--------------------
1992 Mustang GT: Stolen 4/23/03
1993 Mustang GT:
Performance:
AFR 165 pedestal mount 60cc heads, Crane 1.7 Roller Rockers, FRPP EFI Valve Covers, Cobra Intake Manifold, BBK 3/8 Phenolic Spacer, FMS 65mm TB, C&L 76mm Mass Air Meter, BBK Fenderwell Cold Air Intake, BBK 1 5/8" Jet-Hot Shorty Headers, Bassani 2.5" X-Pipe w/ Cats, FMS 3.73 Ring and Pinion Gears, Flowmaster 2 Chamber Mufflers, BBK Aluminum Underdrive Pulleys, B&M Supercooler, PA Full Manual Valve body w/ Trans Brake, TCI Street Fighter Lock up Converter, PA Performance 3G Alternator, FMS Aluminum Driveshaft, Kirban Billet Fuel Pressure regulator, Hurst Quarter Stick
Handling:
MM Standard Length Subframe connectors, MM 4 Point K-Member Brace, MM Strut Tower Brace, Saleen Progressive Rate Lowering Springs, Koni Yellow Shocks, Pro3i Street/Strip LCA's w/ weight jackers
Performance:
*13.27 seconds ¼ mile time
*104mph traps
Posts: 159 | From: San Mateo | Registered: Mar 2002
| :
|
|
Gear Head
JARED
Member # 779
|
posted
No you will not have to modify the shift kit at all.
What gears do you plan on putting in?
--------------------
Support our troops!
Posts: 5685 | From: EASTBAY | Registered: Jan 2002
| :
|
|
FasterDamnit
Bad Attitude
Member # 442
|
posted
Bet you will. LikeIke had to. The techs at TransGo can tell you what valve to modify in the valvebody (just using a specific drill bit) so it doesn't shift into OD whle you are in D. Put the gears in first to see if it needs the change.
JL
--------------------
'92 LX T5
Looked stock, went 11's 11.90 at 115mph.
'65 Mustang 347
www.fordmuscle.com
Livin' in the Carolina Pines
Posts: 2971 | From: NorCal | Registered: Sep 2001
| :
|
|
slow&poor
¯
Member # 961
|
posted
I was planning on putting in 3.73 gears
I really don't want to modify the valvebody again because I basically just installed the shift kit and I don't want to re-do it.
Posts: 159 | From: San Mateo | Registered: Mar 2002
| :
|
|
Gear Head
JARED
Member # 779
|
posted
quote:
Originally posted by FasterDamnit:
Bet you will. LikeIke had to. The techs at TransGo can tell you what valve to modify in the valvebody (just using a specific drill bit) so it doesn't shift into OD whle you are in D. Put the gears in first to see if it needs the change.
JL
He has a 92 mustang. It will only switch into Overdrive if he pushes the shifter in that position. If you leave it in Drive then it will only shift up to third gear.
--------------------
Support our troops!
Posts: 5685 | From: EASTBAY | Registered: Jan 2002
| :
|
|
|
Email this post to someone!
Printer friendly view of this Ford topic
