T O P I C R E V I E W
|
IKE
Member # 435
|
posted
I have the Ford fuel injection and electronic Engine control Book!! I know what the codes stand for But where in the hell do I even start . I see one thing leads to another in this situation. 33= EGR valve opening not detected 41= No HEgo system rich right O2 sensor 66= Mafor Vaf circuit below minimum voltage 91= No Hego system rich right O2 sensor 95= Fuel Pump secondary circuit failure Where do i even start on this one??? I have changed alot of the egr stuff so I know it is working properly!!!
|
T-TopTerror
Member # 480
|
posted
66 is your first thing!!! That is your MAF. That throws everything out of wack. It is one code that code scanner book says replace immediatly. Borrow somebody's sensor disconect battery clear the codes let it run for 5 min. + and re-check.
|
IKE
Member # 435
|
posted
I dont know any one out here with a same year car as mine so Im either going to have to buy one new or. Im going to have to go to the junk yard....
|
T-TopTerror
Member # 480
|
posted
What year and motor type do you have??? There is a way to test the sensor but you need a Digital Storage Oscilloscope (DSO). How many connections do you have in the parts area? Any friends who are mechanics that have this thing? I have "hot wire type" testing instructions if you need them.
|
shade-tree
Member # 298
|
posted
step 1. let the car sit, check the codes again. 66 could be stored and not current. Check the MAF voltage at idle and at say, 2500 rpms. needs to withing range (check Chiltons).rich/lean/etc. check for vacuum leaks, and wiring harness grounds. Have you done anything to the car recently? double check any changes you have made. pull a plug or two and see if it confirms rich/lean condition. As a last resort, consider swapping O2 sensors if yours have a lot of mileage.
|
IKE
Member # 435
|
posted
I have brand new O2 sensors.. I have went over the engine very carefully for vacum leaks. I even changed lines that looked old. I checked the wiring harness to the sensor it is good now im checking the sensor itself....
|
IKE
Member # 435
|
posted
1988 Gt Ho, Aod 132,000 on dial Transgo shift kit 373's gears B/M Hammer shifter K/N Conical B-cam MSD billet distributor Caspers throttle responce calibrator C/L 76mm calibrated #19 injectors 300t ignition FMS wires BBK underdrive pulleys BBk offroad h pipe BBK equal length headers 2 chamber flomasters Energy suspension motor/tranny mount Ac Delete kit 3core radiator autozone special 160 thermostat 180 G Alt Gt fog light fix
|
IKE
Member # 435
|
posted
the plugs look good no signs of them being rich.. As in them being black. They look normal!!
|
shade-tree
Member # 298
|
posted
unplug the negative battery terminal for a minute or two, grab the codes again.did you recently replace: MAF fuel pump ?? Also, when was the last time you cleaned the IAB? (carb cleaner works)
|
IKE
Member # 435
|
posted
I cleaned the Iab it opens and closes freely no sticking.... I will un do the negative and rerun the car again to see if it simmulates!!!! I will let you guys know what happens...IKE
|
st5150
Member # 51
|
posted
If I didn't know any better, it looks like you where working on the car and did something to make the motor die.The fuel pump code is BS, ignore it. Your EGR is either stuck shut or there is a problem getting vacuum to it. Here are the 'important' codes that affect idle, drivability and power:
MAF- Either is bad (kinda rare) or you did something that killed the motor while it was idling. Unplug the battery for a few seconds and run the codes again, see if it comes back ASAP.
O2 sensor codes.... it looks like they're not pluged in..... or maybe you got the wrong ones? They are grounded to the back of the drivers side head. Follow the braided steel strap and see where it bolts in. In the same bolt there should be another wire that grounds the O2's.
|
IKE
Member # 435
|
posted
I have vacum to the egr i pull the tube and there is air so its not that!! I reset the computer to see what happens??? Im kind of wondering now if those are the right O2 sensors i just bought them and installed them about 3 months ago. I had this problem previously to that. so I know its not the O2 sensors. I will check this wiring that you are talking about. I will see if I can find out where they ground is connected at....
|
st5150
Member # 51
|
posted
Well at idle the EGR is closed so when you pull its vacuum line there should be NO vacuum to it. The EGR only opens durring steady cruise or durring the engine running EEC test. To see if the EGR is getting vacuum, run the engine running test with your finger over the EGR vacuum line. Half way through the test you sould feel suction from the line as the EEC tests the EGR. If you don't feel the suction, then your problem is down stream. I have a feeling all your codes are due to one problem. MAF, O2's, EGR. It shouldn't be hard to find another 5.O and swap MAF's for a few minutes to help trouble shoot.
|
IKE
Member # 435
|
posted
Hey there is vacum at idle what would cause this !! know Im getting somewhere!!
|
IKE
Member # 435
|
posted
I have vacum at idle!!! Could not type last post pardon me...
|
JUSTIN
Member # 586
|
posted
.
|
sshir16
Member # 824
|
posted
.
|