T O P I C R E V I E W
|
svt3773
Member # 4759
|
posted
what kind of heads and cam could i put on my 85 gt it's stock block just have an edelbrock manifold n carb.
|
92stangLX
Member # 3252
|
posted
You should be able to put any aftermarket 302 heads on there w/o issue.
You may run into piston to valve clearance issues with a cam though. You should definitely check clearance on whatever cam you decide to go with.
|
PopTheHood
Member # 7040
|
posted
I have the twisted wedge heads and stage 1 cam and i like it... i also have an 85 ![-](http://i95.photobucket.com/albums/l142/hot85fifty/10-31-2006-075.jpg) ![-](http://i95.photobucket.com/albums/l142/hot85fifty/9-29-2006-85.jpg) [ November 03, 2006, 01:14 PM: Message edited by: PopTheHood ]
|
svt3773
Member # 4759
|
posted
quote: Originally posted by PopTheHood: I have the twisted wedge heads and stage 1 cam and i like it... i also have an 85 ![-](http://i95.photobucket.com/albums/l142/hot85fifty/10-31-2006-075.jpg)
do you have a stock 85 block. because my cousin put the same set-up you have on his 86 gt and had cleareance issuses with those came and heads on his flat piston block. anybody else could help with this issue. planning to get gt-40's but dont know if i'll run into troble with piston and valve clearance issue depending on the cam to use.
|
HaulinAssMaro
Member # 541
|
posted
quote: Originally posted by svt3773: quote: Originally posted by PopTheHood: I have the twisted wedge heads and stage 1 cam and i like it... i also have an 85
do you have a stock 85 block. because my cousin put the same set-up you have on his 86 gt and had cleareance issuses with those came and heads on his flat piston block. anybody else could help with this issue. planning to get gt-40's but dont know if i'll run into troble with piston and valve clearance issue depending on the cam to use.
An 85 shortblock is the same as the 87-92 shortblock.They have Factory Forged Pistons,Roller Cams etcc... with the same valve clearence as the 87-92 shortblocks.You can use any of the common heads/cams without any issues.
|
svt3773
Member # 4759
|
posted
thanks matt
|
HaulinAssMaro
Member # 541
|
posted
quote: Originally posted by svt3773: thanks matt
no prob
|
PopTheHood
Member # 7040
|
posted
I bought an 87-93 replacement motor.. then i changed the heads, cam, intake.. with this setup i have no problems, except hood clearence. the air cleaner box presses against the lining under my hood. But the hood still closes.. 86 pistons most likley will have piston to valve clearence because they dont have valve relives. but im not sure.
|
PopTheHood
Member # 7040
|
posted
Here is a pic of the pistons in my motor...You can see the notches in them.. i dont think 86's have these..
|
svt3773
Member # 4759
|
posted
that's what i was worried about but i guess 85 motor is different than a 86 motor. right?
|
PopTheHood
Member # 7040
|
posted
I dont think they have the notches in the pistons
|
silverLX
Member # 3207
|
posted
85's have valve reliefs 86's DONT have valve reliefs 87-92's have valve reliefs.
85, 87-92 shortblocks are the same. 86 and 93 motors are the ones I usually stay away from.
|
asskickn88
Member # 4957
|
posted
The 85 had a roller cam if it came with a 4 bbl and 5 speed, if it was an AOD car it had a flat tappet cam and TFI injection.
|