T O P I C R E V I E W
|
510.86.notch
Member # 9892
|
posted
i'm replacing my struts and shocks today on my 89 coupe and was wondering about my alignment?can you mark it and try to set them in the same place or do i just got to suck it up and get a alignment?are there any tricks or tips?any help will be greatly appreciated.thanks cafords [ April 05, 2011, 04:06 PM: Message edited by: 510.86.notch ]
|
68stanger
Member # 7842
|
posted
your not messing with any tie rods or caster camber plates. It should be remove and replace....
|
Blind
Member # 3052
|
posted
the strut to spindle attachment point has a -huge- effect on camber, with those 2 bolts loose you can move the spindle enough to change the camber by almost a full degree with some struts.
an alignment should definitely be done afterwards.
|
Adam5.0
Member # 6995
|
posted
no alignment needed.
|
510.86.notch
Member # 9892
|
posted
no caster camber plates only changing brakes,spindles,struts and shocks.i'm trying to get some springs.also i went from 4 cylinder rims to 17x9s i'm thinking i need a alignment?thanks for the info.
|
89bluenotch
Member # 7454
|
posted
yeah your going to need one changing the spindles
|
510.86.notch
Member # 9892
|
posted
quote: Originally posted by 89bluenotch: yeah your going to need one changing the spindles
yea i figured.just double checking.also having trouble removing the struts can't seem to get the bolt off on the top its just spinning. i held the top with a big flat head.any suggestions will be greatly appreciated.thanks
|
Blind
Member # 3052
|
posted
impact gun always works for me, sometimes it helps to put a jack under that control arm and jack it up.
|
510.86.notch
Member # 9892
|
posted
quote: Originally posted by Blind: impact gun always works for me, sometimes it helps to put a jack under that control arm and jack it up.
i got the bottom off that connects to spindle.can't get the top off.i also tried what you suggested.
|
Adam5.0
Member # 6995
|
posted
impact it and it will come off
|
510.86.notch
Member # 9892
|
posted
ok thanks i'll try that tomorrow.
|
gercolla1
Member # 3068
|
posted
if you you need a alignment go to tidewater tires this place knows mustangs
http://www.yelp.com/biz/tidewater-tire-oakland
|
510.86.notch
Member # 9892
|
posted
thanks thats was going to be my next question.also do you happen to know they're prices?
|
gercolla1
Member # 3068
|
posted
think its 50 bucks it would be best to call them and schedule a appt
|
SteveL
Member # 1241
|
posted
Blind has it right but you can (and should) outline the position of the current struts on the spindle. Install the new ones and try to match up the outline which can be tricky if you change brands. If you're careful, you can certainly get within a couple of tenths of a degree on camber.
While you're there, check the spacing between the inside top egde of the rim and the strut. Even if it screws up your current alignment, you want to set that before paying for the next alignment. [ April 06, 2011, 01:01 AM: Message edited by: SteveL ]
|
510.86.notch
Member # 9892
|
posted
quote: Originally posted by SteveL: Blind has it right but you can (and should) outline the position of the current struts on the spindle. Install the new ones and try to match up the outline which can be tricky if you change brands. If you're careful, you can certainly get within a couple of tenths of a degree on camber.
While you're there, check the spacing between the inside top egde of the rim and the strut. Even if it screws up your current alignment, you want to set that before paying for the next alignment.
actually was thinking about that.my rim/tire were rubbing pretty bad had to install 1/4'' spacer in front.can you elaborate a little more on what you were saying.maybe in dummy term.i didn't comprehend what you were putting down.thanks for all the input i need it.
also using different strut and spindle so i couldn't mark. [ April 06, 2011, 02:26 AM: Message edited by: 510.86.notch ]
|
510.86.notch
Member # 9892
|
posted
quote: Originally posted by gercolla1: think its 50 bucks it would be best to call them and schedule a appt
thanks bro defiantly going to make a appointment there.
|
Blind
Member # 3052
|
posted
quote: Originally posted by 510.86.notch: quote: Originally posted by SteveL: Blind has it right but you can (and should) outline the position of the current struts on the spindle. Install the new ones and try to match up the outline which can be tricky if you change brands. If you're careful, you can certainly get within a couple of tenths of a degree on camber.
While you're there, check the spacing between the inside top egde of the rim and the strut. Even if it screws up your current alignment, you want to set that before paying for the next alignment.
actually was thinking about that.my rim/tire were rubbing pretty bad had to install 1/4'' spacer in front.can you elaborate a little more on what you were saying.maybe in dummy term.i didn't comprehend what you were putting down.thanks for all the input i need it.
also using different strut and spindle so i couldn't mark.
when you have the new strut bolted in on top, loosely install the 2 lower bolts, then throw the tire on, grab the wheel at 12 and 6 o'clock and push/pull and you'll notice how much you can move the camber at the wheel itself using only the spindle/strut alignment, if you push in at 12 o'clock all the way, you might be putting the tire/wheel too close to the strut for clearance, so play with it until you have enough room.
|
SteveL
Member # 1241
|
posted
That's the process but how much space you get between the tire and the strut depends on which spindles and which rims you have.
|
510.86.notch
Member # 9892
|
posted
quote: Originally posted by Blind: quote: Originally posted by 510.86.notch: quote: Originally posted by SteveL: Blind has it right but you can (and should) outline the position of the current struts on the spindle. Install the new ones and try to match up the outline which can be tricky if you change brands. If you're careful, you can certainly get within a couple of tenths of a degree on camber.
While you're there, check the spacing between the inside top egde of the rim and the strut. Even if it screws up your current alignment, you want to set that before paying for the next alignment.
actually was thinking about that.my rim/tire were rubbing pretty bad had to install 1/4'' spacer in front.can you elaborate a little more on what you were saying.maybe in dummy term.i didn't comprehend what you were putting down.thanks for all the input i need it.
also using different strut and spindle so i couldn't mark.
when you have the new strut bolted in on top, loosely install the 2 lower bolts, then throw the tire on, grab the wheel at 12 and 6 o'clock and push/pull and you'll notice how much you can move the camber at the wheel itself using only the spindle/strut alignment, if you push in at 12 o'clock all the way, you might be putting the tire/wheel too close to the strut for clearance, so play with it until you have enough room.
ok thats makes sense.thanks a million.also running stock v8 four lug spindle off a turbo coupe thunderbird and running 17x9 four lug 03 cobras all the way around.
|