|
Author
|
Topic: Suspension Suggestions?
|
Bulkster90
¯
Member # 11621
|
posted
 
 
Got a 89LX. Looking to start upgrading the suspension. The only upgrade to the suspension would Eibach Sportline lowering springs. Otherwise it is completely stock. It is my daily driver. Im probably gonna get parts here and there so just tryin to get some suggestions on where to start. Not good with all the acronyms, some links would be great. Thanks.
here are some pics of the car.
dont mind the paint job, just bad lighting ![[Roll Eyes]](rolleyes.gif) lol (thats up next after suspension)
[ April 30, 2012, 02:16 AM: Message edited by: Bulkster90 ]
--------------------
1992 LX Coupe
2011 Coyote 5.0
Posts: 223 | From: Fairfield | Registered: Jan 2012
| :
|
|
Saleen 00-768
¯
Member # 9379
|
posted
get good shocks if you already got sportlines
KONI
BILSTIEN
TOKIKO ..ect
subframeconnectors should be #1 suspension mod perferably full length
id throw a panhard bar in it after that jus because how much more stable it makes the car while cornering hard (a must have in a fox that handles)
then caster camber plates for optimum/more agressive alignment
then id do ALL urathane bushings up front and a stut brace
MAXIMUMMOTORSPORTS.COM < lots of good TECH information and just about everything you need for suspension
[ April 30, 2012, 02:33 AM: Message edited by: sneakyfox90 ]
--------------------
'00 Saleen SC #768
'90 GT
'90 California Edition (sold)
'87 Saleen #264 (sold)
Posts: 1664 | From: NOR✯CAL | Registered: Aug 2009
| :
|
|
NEIGHT
¯
Member # 8741
|
posted
1. Full-length subframe connectors
2. Upper N lower control arms in the rear
3. Shocks
4. Caster camber plates
5. Strut tower brace
6. Tubular K-member setup
--------------------
-Savage Habits-
1992 Summer Edition
1986 Hatch- catfish killer
1964 Impala hard top
Posts: 18535 | From: EA$T $IDE REDWOOD CITY | Registered: Nov 2008
| :
|
|
Bulkster90
¯
Member # 11621
|
posted
Adjustable or just regular lower control arms?
whats the difference.
--------------------
1992 LX Coupe
2011 Coyote 5.0
Posts: 223 | From: Fairfield | Registered: Jan 2012
| :
|
|
93nIFtYgT
¯
Member # 7804
|
posted
Same question on what's the difference between adjustable & not?? How about torque box braces? & with the K- member? Is that something that takes a little more mechanically inclined skills? Or should I be left up to pros? I've read things about people can't get it aligned correctly. I wanna start my suspension soon also
Posts: 33 | From: East Bay | Registered: Jul 2007
| :
|
|
Greasy
¯
Member # 5258
|
posted
quote:
Originally posted by 93nIFtYgT:
Same question on what's the difference between adjustable & not?? How about torque box braces? & with the K- member? Is that something that takes a little more mechanically inclined skills? Or should I be left up to pros? I've read things about people can't get it aligned correctly. I wanna start my suspension soon also
These are adjustable lower control arms, you can actually adjust the spring perch up or down to raise or lower the vehicle.
Here are some Battle Boxes that I installed over the weekend, I did all four but only have a pic of the lowers.
It was an easy install, I don't know how mechanically inclined you are but all you need are some basic hand tools.
--------------------
'93 Cobra-Coyote Powered
'03 DSG Cobra
'13 Dodge Cummins
'14 Rubicon X
Posts: 3272 | From: North Dallas | Registered: Jan 2005
| :
|
|
1fastmach1
¯
Member # 10137
|
posted
Baseline suspension Is good too ![[worship]](graemlins/worship.gif)
--------------------
REDLINE MOTORSPORTS CC EST 2011
1993 CHP sold
2004 mach 1 408 Windsor n20 fed
R.I.P. JORGE GUTIERREZ JR
6/13/1982- 11/05/2013
Posts: 2592 | From: clawwwitter to 7th st | Registered: Jul 2010
| :
|
|
FivePTSlow
¯
Member # 7682
|
posted
quote:
Originally posted by Bulkster90:
Got a 89LX. Looking to start upgrading the suspension. The only upgrade to the suspension would Eibach Sportline lowering springs. Otherwise it is completely stock. It is my daily driver. Im probably gonna get parts here and there so just tryin to get some suggestions on where to start. Not good with all the acronyms, some links would be great. Thanks.
here are some pics of the car.
dont mind the paint job, just bad lighting lol (thats up next after suspension)
This all really depends on how much you want to spend.
-Sub Frame Connectors top the list for sure. They're relatively inexpensive and make the car feel much more solid with a lot less flex. I used BBK SFC's with seat support brackets. Make sure to have them welded in. Bolting them in helps, but is nowhere near as firm as when they're welded in.
-Polyurethane Bushings & Mounts are another really good bang for the buck. You can order anything made from Energy Suspension through Autozone's special order. I outfitted my entire Mustang with poly bushings & mounts and what a difference! Much less body roll, more predictable cornering/braking etc I have poly sway bar bushings, end link kits, transmission crossmember bushings, transmission mount, motor mounts etc
-Coil Overs I have only done coil overs on the front(I used a retrofit sleeve kit from qa1 on top of lakewood 90/10 struts), but man huge difference. My car rides much smoother now. I'm not sure what it's called, but the "delay" so to speak of when you run over a bump or pothole in the road is no longer there. I suppose it allows your suspension to work faster and absorb more rather than transfer that to the body
-Tubular K Member & Tubular A Arms I have these installed on my car. I used D&D Motorsports Tubular K Member and Granatelli Tubular A Arms(front control arms) Between the K Member, A Arms, and Coil Overs I saved about 70lbs over stock parts and have much more room to work on everything under the car. Once the all of this stuff was installed the car felt a lot more balanced from front to back and a heck of a lot more rigid. Between all of the stuff I've listed above I now have nearly zero body roll, so if I go around a corner fast it will start sliding with no roll at all, but with the smallest correction I can be going straight as an arrow easily.
-Control Arms I used UPR Chromoly Adjustable length control arms. They have a poly bushing in the back and a spherical bushing up front. I have no wheel hop and with all other mods if I mash the throttle all I get is wheelspin and I go completely straight with very minimal side to side movement, so it feels a lot more safe and predictable. No more fishtailing and nearly hitting the guy next to you.
-Caster/Camber Plates these are necessary to run proper alignment and have a lot more alignment freedom. I used the Maximum Motorsports with my coilover setup because it was one of the few manufacturers that said you can. Most others say they're too weak and will fail sending your strut through your hood.
These are just my experiences. All other cars I've mostly stuck with drag springs and drag shocks/struts with no swaybars etc. That setup is very sloppy and even if it helps go down the 1/4 mile faster it's not worth driving around like that on the road for me any longer.
--------------------
2011 GT/CS 5.0 + Boost(Procharger)
90 Bronco 5.8 Lifted
05 SRT-4 24PSI E-85 at least 50 million hp
07 Harley VROD NRS Stage 1
Posts: 1857 | From: Sacramento | Registered: May 2007
| :
|
|
93nIFtYgT
¯
Member # 7804
|
posted
Nice.. What would you give each task a rating of from 1 - 10 on difficulty to perform. I would say I'm about a 6 or 7 when it comes to mechanical work.. The main thing I am concerned about is the K-member? Do you need an engine lift? & what else is involved?
Posts: 33 | From: East Bay | Registered: Jul 2007
| :
|
|
FivePTSlow
¯
Member # 7682
|
posted
quote:
Originally posted by 93nIFtYgT:
Nice.. What would you give each task a rating of from 1 - 10 on difficulty to perform. I would say I'm about a 6 or 7 when it comes to mechanical work.. The main thing I am concerned about is the K-member? Do you need an engine lift? & what else is involved?
Most of everything is pretty easy. Sub Frame connectors I took to my buddy's shop to have them welded in I didn't bother bolting them in at all, so unless you know how to weld you will have to take them to a shop. I don't know how to weld very well, so the difficulty for me would be high on these. If you know how to weld and have a lift then the difficulty would be very low. All that really needs to be done is to prep for welding, check fitment, mock up, tack weld, weld, then paint over the welds, so that they dont rust.
Shocks/Struts/Coilovers, Caster/Camber plates are all very easy. Control arms are super easy, polyurethane bushings super easy. I would put all of these at a 5 or less as far as difficulty.
K Member: I would guess that this really depends on which K member you purchased. I went to my buddies shop and used a lift, air tools etc for my install and it took several hours even with all the right tools. It wasn't a difficult install, but it took a lot of time. I'm sure I could have installed this in my garage, but I really wouldn't want to. Getting mt K Member to line up was hard enough on a lift with 2 people and plenty of room to work in all directions. As far as difficulty I would probably put this right around a 7
--------------------
2011 GT/CS 5.0 + Boost(Procharger)
90 Bronco 5.8 Lifted
05 SRT-4 24PSI E-85 at least 50 million hp
07 Harley VROD NRS Stage 1
Posts: 1857 | From: Sacramento | Registered: May 2007
| :
|
|
Duncan Motors
¯
Member # 7045
|
posted
sub frames, torque boxes, iron 50 does a great job and is very inexpensive for a very top notch job.then as for suspension goes, its really the skys the limit depending on your budget
Posts: 6310 | From: Vallejo | Registered: Sep 2006
| :
|
|
fredfifty
Since
9/2010
Member # 10320
|
posted
in order to get the sub frames, might need to take your car to a body shop and see if the frame is straight first...
--------------------
RIP EDSON VELORO
IM A NOOB, EXCUSE ME. THANKS.
92 LX Coupe 5.0 CARB'd BOLT-ONS SMOG LEGAL
62 Rag Impala
Posts: 4948 | Registered: Sep 2010
| :
|
|
fast305s
¯
Member # 11897
|
posted
nothing puts power down better to the floor or around the corners than a good set of tires my friend.
--------------------
Built, not bought.
95 mustang gt
73 f-100
06 powerstroke
Posts: 154 | From: brentwood | Registered: Apr 2012
| :
|
|
fredfifty
Since
9/2010
Member # 10320
|
posted
quote:
Originally posted by fast305s:
nothing puts power down better to the floor or around the corners than a good set of tires my friend.
for some reason i feel like a dos equis right now lol
--------------------
RIP EDSON VELORO
IM A NOOB, EXCUSE ME. THANKS.
92 LX Coupe 5.0 CARB'd BOLT-ONS SMOG LEGAL
62 Rag Impala
Posts: 4948 | Registered: Sep 2010
| :
|
|
fast305s
¯
Member # 11897
|
posted
haha, stay gripped up my friends
--------------------
Built, not bought.
95 mustang gt
73 f-100
06 powerstroke
Posts: 154 | From: brentwood | Registered: Apr 2012
| :
|
|
Bulkster90
¯
Member # 11621
|
posted
Thanks for the info guys
--------------------
1992 LX Coupe
2011 Coyote 5.0
Posts: 223 | From: Fairfield | Registered: Jan 2012
| :
|
|
Email this post to someone!
Printer friendly view of this Ford topic
