T O P I C R E V I E W
|
Drift-GT
Member # 762
|
posted
Put all these part together to put into a Nissan 240sx. We built conversion mounts, headers, and a buch of other goodies. Project has changed directions.
Willing to sell the parts as a kit or individually. Price for the kit with all the parts listed $2,500.00 + S/H (if you are not local). If you want to just buy individual parts shoot me a PM/call/e-mail and we can figure out a price.
Conversion parts:
- Custom headers / custom oil pan / custom motor mount / custom tranny mount - AN fittings and earl's perform-o-flex high pressure hose for power steering conversion directly to 240sx rack - Includes all sensors for MAP or MAF ECU setup. - Complete MAP harness/ECU - Torn down MAF harness ready to solder up and go that route if you want (you wil still need the MAF ECU)
Stock Ford Parts:
- T5 Tranny w/ used clutch/flywheel, shifter/handle - Stock Mustang T5 Transmission crossmember - Stock Mustang drifeshaft - 5.0 Short Block w/ parts unassembled - 5.0 Heads - Stock oil dipstick - Water Pump - x2 Alternator w/mounting brackets/tensioner - x2 Air Condition Pump W/mounting brackets - x2 Flywheel - x1 Used Power Steering Pump w/mounting brackets - x1 NEW power steering Pump w/mounting brackets - Smog pump (only for you CA people haha) - Starter - Starter silinoid - Stock intake Elbow w/ Air box w/filter - Mustang Clutch/brake Pedal assembly - Clutch cable / Quadrant - Stock Headers - Stock Lower Intake Manifold - Stock Upper Intake Manifold - Stock throttle body - Stock fuel rail w/19lbs injectors - Stock EGR plate W/EGR valve - Stock valve covers - Stock ignition coil
2nd Engine:
- Assembled Long block - Installed Hot Aftermarket E303 Cam - Underdrive Crank Pulley - High-Flow Water pump
Aftermarket goodies:
- New Ford Racing Mini Tq Starter - New Polished 75mm Thorttle Body - New BBK Throttle Body Gasket - New Edelbrock Performer Intake Mani Gasket Set - New Ford Motorsport Chrome distributor hold down clamp - New Hamburg Cork Oil Pan Gasket - MSD 6AL w/ Pillls - New MSD Vibration Mounts - New Vehicle Speed Sensor - New EFI Spacer Kit Performer Rpm 3/8 inch - New Energy Suspension Tranny Mount Urethane - New Ford Motorsports AC Eliminator Kit - Moroso Solid Motor Mounts - New Chrome Oil Dipstick - New Smog Pump Elim Bracket (moves PS pump into a better upright position) - New Chrome Msd Blaster Coil - New Universal Chrome Coil Bracket - Howe Eng. 1 5/16 stroke slave cylinder pull type - Wilwood 1 Inch Master Cylinder - Earls AN adapters w/high pressure SS line for master to slave connection (pre-built) - New Ford Motorsport larger racing Oil Pump Shaft - New ARP Pressure Plate Bolts - New Milidon Ford Oil Pan Studs - New Zoom Clutch/Pressure Plate/TOB/Pilot Bearing - 30 LB Injectors w/ matched 75mm Maf (these injectors can also be used with MAP but tuning will be required) - Edelbrock RPM Manifold - New Edelbrock gasket set for manifold - New Trick flow 3/8" intake manifold spacer - Larger capasity SN 95 (94-95) fuel rails w/BBK Fuel Pressure regulator & BBK Fuel Pressure Gauge pre-installed
- Polished Tall Ford Racing Valve Covers - Msd Plug Wires w/ MSD Cap / Rotor / installed on stock distributor - New oil filter relocation kit
Thanks for looking , Dana drosborn_jr@yahoo.com 510-299-7572
|
LX306hatch
Member # 9151
|
posted
Pm sent very interested
|
Drift-GT
Member # 762
|
posted
All PM's sent back
|
kennebellgt
Member # 8395
|
posted
pm sent
|
FATALPNY408
Member # 8896
|
posted
Pm sent
|
Drift-GT
Member # 762
|
posted
All PM's sent back
|
Drift-GT
Member # 762
|
posted
All PM's and e-mails sent
|
quicksilver91
Member # 9034
|
posted
still got the air box???
|