|
Author
|
Topic: What time will I hit with this combo
|
1SLOWLX
¯
Member # 558
|
posted
 
 
91 lx 347 stroker with an s-trim at 10psi
5 speed 36lb injectors all the msd bullshit, going to run on 26 by 10.5 slicks 3.73 gears edelbrock perfromer heads ported and polished crower cam and a bunch of other things hopeing to go somewhere in the 11's let me know what you think I probably missed a bunch of shit also what do you think it will dyno at?
Thanks everyone Albert
--------------------
Built Tuff with your stuff ;)
Posts: 5231 | From: bay area | Registered: Nov 2001
| :
|
|
|
|
Stimson
_
Member # 51
|
posted
Those heads, even ported are too small for your a 302, let alone a boosted 347. It should make around 430+ RWHP and run well into the 12's/high 11's.
Posts: 2373 | Registered: Jun 2000
| :
|
|
|
|
|
|
1SLOWLX
¯
Member # 558
|
posted
but when are are supercharging an engine flow is important but not as important as if it was a all motor car. I know the heads aren't the best but the supercharger should make up for the bad heads in my view. I just want this thing to go into the 11's it should if it hooks up
--------------------
Built Tuff with your stuff ;)
Posts: 5231 | From: bay area | Registered: Nov 2001
| :
|
|
|
|
|
|
1SLOWLX
¯
Member # 558
|
posted
The fuel system are as follows aero fuel rails t-rex pump 190 intank pump and for the electronics it goes pro-m77 power pipe it will have a custom chip when running by bryon. The combo is going to have the 2.95 pulley on the s-trim hopeing for 10+ pounds of boost! I mean I know the intake and heads aren't all that but I already had them and spent all my money building a bulletproof bottom!
--------------------
Built Tuff with your stuff ;)
Posts: 5231 | From: bay area | Registered: Nov 2001
| :
|
|
|
|
1SLOWLX
¯
Member # 558
|
posted
I have heard that the edelbrock heads are garbage but the will flow near the trick flow with maybe at the most 20cfm less they are better than a stock head.
--------------------
Built Tuff with your stuff ;)
Posts: 5231 | From: bay area | Registered: Nov 2001
| :
|
|
|
|
66fastback
¯
Member # 657
|
posted
You should easily hit the 11's if you know how to drive. I had a 93 lx stock short block with the same heads and a cobra intake an A trim and ran 11.7 @ 119, on cheaters with stock suspension.
--------------------
http://www.mustangdoctor.com
Posts: 42 | From: Sacramento | Registered: Dec 2001
| :
|
|
Stimson
_
Member # 51
|
posted
Albert1- That 2.95 pulley should easily get you your boost levels. I think if anything is going to limit you on the dyno, its going to be your fuel system. What kind of FMU are you running?
Jeff S- 6037's flow, what.... 210 cfm on the indea out of the box going from memory? I forget their port volume, but its not small enough to make the 210 "impressive" if I remember right. I think they have a similar port volume as AFR's, but flow nearly 40 cfm less. Whats the most you've seen 6037/6039 heads flow? I think 275 or so is the maxed I've seen/heard a set of those heads flowing. I know back in the days, 5.O guys options where more limited, but now if you want a 275 cfm head, you can port some TW's a bit or get some AFR 185's. Doesn't make sense to buy some "little" heads and spend $800 on port work them anymore. I think I know which NA 347 you're talking about.... isn't that a high compression, race gas, solid roller, carburated car? Just goes to show that increased head flow is only the 'potential' to make power.
I know there are exceptions to every rule, but I'm just talkinga bout the "average" 5.O here.
Just my two cents....
-Sawson
Posts: 2373 | Registered: Jun 2000
| :
|
|
1SLOWLX
¯
Member # 558
|
posted
I am running a stock fmu with a 4 to one cal in it. The only thing left stock in the fuel system is the lines from the tank to the engine and the pickup in the tank. as for my suspension it has steeda aluminum upper and lower control arms. 50-50 drag stocks and 70-30 front struts. It has sub frame connector and a strut tower brace also caster camber plates as well. I think the fuel system that is on it right now should support about 500 the rails are aeromotive so we will see thanks everyone
Albert
--------------------
Built Tuff with your stuff ;)
Posts: 5231 | From: bay area | Registered: Nov 2001
| :
|
|
Email this post to someone!
Printer friendly view of this Ford topic
