|
Author
|
Topic: Custom Cam for TFS Heads w/ stock shortblock
|
JBeezy53
CAFords OG
Member # 3960
|
posted
 
 
Cam is new, installed in the block but never run. Spec'd out by HiTech Motorsports. This cam is for Trickflow Twisted Wedge heads and is meant to be used with a stock shortblock, and a Performer RPM/ Trick Flow Track Heat/ SysteMax intake and 3.73 gears. Also a good cam for a dual plane carb intake. This is a street cam for a street car, and will make GREAT power from 1500rpm up to 6000 rpm.
Cam was originally $335 from HiTech. Selling for $220. PM me if you are interested.
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
Camara90
1%
Member # 134
|
posted
Should be a pretty stout cam, similar to the one a run but a tad bigger. That intake lobe is no joke!
--------------------
92GT,stock short block,9:1 TFS 170's,perf rpm,custom cam,1 5/8 shorties,C4 trans.
std. 356hp, 350tq
11.85@111.9mph on motor.
Posts: 2351 | From: 707 | Registered: Jan 2001
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
quote:
Originally posted by Camara90:
Should be a pretty stout cam, similar to the one a run but a tad bigger. That intake lobe is no joke!
That's good to know since you put down damn good numbers for your combo.
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
FivePTSlow
¯
Member # 7682
|
posted
Did they say if this would work with the stock TFS TW Valve Springs? I'm pretty sure TFS says only up to .550 lift
--------------------
2011 GT/CS 5.0 + Boost(Procharger)
90 Bronco 5.8 Lifted
05 SRT-4 24PSI E-85 at least 50 million hp
07 Harley VROD NRS Stage 1
Posts: 1857 | From: Sacramento | Registered: May 2007
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
quote:
Originally posted by FivePTSlow:
Did they say if this would work with the stock TFS TW Valve Springs? I'm pretty sure TFS says only up to .550 lift
Upgraded springs will be needed. It even says "springs required" on the cam card.
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
ttt
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
ttt
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
v-town coupe
fordologist
Member # 2771
|
posted
quote:
Originally posted by JBeezy53:
quote:
Originally posted by FivePTSlow:
Did they say if this would work with the stock TFS TW Valve Springs? I'm pretty sure TFS says only up to .550 lift
Upgraded springs will be needed. It even says "springs required" on the cam card.
I think what he was reffering to is that TW heads allow you to run up to .550 lift before the valve starts to hit the piston.
Posts: 4597 | From: the V-town | Registered: May 2003
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
quote:
Originally posted by v-town coupe:
quote:
Originally posted by JBeezy53:
quote:
Originally posted by FivePTSlow:
Did they say if this would work with the stock TFS TW Valve Springs? I'm pretty sure TFS says only up to .550 lift
Upgraded springs will be needed. It even says "springs required" on the cam card.
I think what he was reffering to is that TW heads allow you to run up to .550 lift before the valve starts to hit the piston.
This cam was specifically designed to work with a stock short block so that taken into account by Hi-Tech. It has been installed and clayed in a motor and has came within specs.
The lift ratings from the companies are conservative. For example I have ran 2.02 Edelbrock heads on stock short blocks that have not been fly cut with no issues. Lift is not the only factor that determines when/if a valve will contact the piston.
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
ttt
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
ttt
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
JBeezy53
CAFords OG
Member # 3960
|
posted
quote:
Originally posted by Camara90:
Should be a pretty stout cam, similar to the one a run but a tad bigger. That intake lobe is no joke!
Still for sale.
Check Camara90's sig, his numbers are damn good with basically a stock shortblock.
--------------------
89 Gt
98 Cobra
88 Notch
05 GSXR 750 Blk/Yel
Posts: 1782 | From: Sacramento, Ca | Registered: Jan 2004
| :
|
|
Email this post to someone!
Printer friendly view of this Ford topic
