This is topic Various Fox engine, drveline and some suspension parts in forum FOR(D) SALE: at Northern California Ford Owners  .


To visit this topic, use this URL:
https://californiafords.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=5;t=109466
Posted by Jack Hidley (Member # 12571) on :
 
I’m still trying to get rid of a lot of stuff in my garage. Unless noted, all parts are for a Fox Mustang. All parts are located in Danville CA 94526. All correspondence to jhidley at comcast dot net. NO PMs please. Weights are listed after most items. Add about 10% for external packaging and go to the UPS website if you need a shipping estimate. No offers to include shipping costs.

Listed first are the aftermarket parts. The stock Ford parts are below that. Non Mustang parts are at the very bottom of the post.

Edelbrock Performer EFI intake manifold for 302 Ford $400. Used, very clean.
Both the upper and lower have been Extrude Honed. The upper was lightened and ported for a 75mm TB. It was then anodized black, then powder coated black. The top of the upper has a pipe plug to allow easy access to the center bolt. The upper also includes 4 ARP stainless steel studs for mounting the TB and EGR spacer. Includes a phenolic spacer and both gaskets between the upper and lower. The lower has been milled some to match the port location of some AFR 165 heads that were milled 0.024". Exact measurements of the manifold available upon request.

K&N FIPK (filter, brackets, oil and cleaner) NIB. make offer
57-2511, 94-95 5.0 Mustang, 7lbs
57-2501, 86-88 5.0 Mustang, speed density only. Filter connects to 3.5" tube. Two available. 6lbs

Auto Specialties pullies. All NIB and gray color.
94-95 Mustang GT 5" crank pulley and 2.75" alternator pulley, 1lbs
527728/527775 96 Mustang/94-96 T-bird. 6.5" water pump, steel, 2.75" alternator, steel, 5.25" crank, aluminum, 6lbs.
1986-93 alternator 2.5" steel pulley, 1lbs

RAM, 434 10.5" pressure plate, $75, 19lbs.
2,600lbs clamping force. 560 ft-lbs of torque capacity with organic disc.
Mounted to flywheel, but never used. Essentially brand new.

RAM 305M 10.5" organic friction disc. 1-1/16"-10 splines, sprung hub, no or very thin marcel. NIB, $75, 5lbs.

RAM 900 10.5" sintered iron friction disc. 1-1/16"-10 splines, sprung hub, with marcel.
Must be used with RAM flywheel due to metalurgical issues with stock flywheels.
NIB, $100, 5lbs.

1 set of used Hawk HB125 HPS front pads. 50% material left. $20, 4lbs.

1 set of NIB Hawk HB239 HPS front pads. These fit phenolic piston 73mm front calipers. $50, 5lbs.

1 set TRW MS2590P-10 main bearings for SBF. $10.

1 set TRW CB634P-10 rod bearings for SBF. One bearing is slightly scratched up and may not be useable. $10.


Stock parts are below. All parts are for an 87-93 Fox Mustang. Make a reasonable offer and it’s yours.


164 tooth flexplate. Bolts to a standard 6 bolt SB Ford crank. Has E0SP-AA part number on counterweight (first used on 1980 T-bird). Unknown application.

Hold down spider for roller lifters in 302 block. One available.

Stock TB with IAC valve and EGR spacer.

IAC valve.

Stock MAF meter. 1988 model with oval connector and MAF bracket.

Stock MAF meter. 1991 model with rectangular connector and MAF bracket.

Alternator/air pump bracket with alternator and tensioner. No idler pulley.

Steel front bracket that holds AC compressor and PS pump together near serpentine belt. Two available.

Small aluminum bracket that holds AC compressor to cylinder head. Two available.

K&N panel air filter.

Stock T5 shifter base. No handle or hardware. 13-52-598-065.

Stock rear brake hose from chassis to differential. Two available.

Baer PBR rear brake dampers. These are cast iron weights about 3" OD that bolt to part of your PBR brake caliper bracket to stop brake moan.

Various spark plug wires. Either new or very good condition.

Accel 9000 Extreme Ultra high temp 8mm black

Coil wires (90 on both ends) 18" two available. Coil end goes on a stud, but has a short boot with one ring around the OD. Not the standard Ford coil style.

Plug wires 30.5" long (90 on distributor end, 135 on plug end) three available

Motorsport 9mm silicone blue plug wires cylinders 1, 2, 5 and 8 (90 to 135)

Complete 28 spline 8.8" traction loc. Complete except no ring gear on it.

Complete 1987-93 5.0l upper and lower intake manifold. Includes TB, EGR spacer, injectors, fuel rail, coolant hose, etc.

Four 8.8" shock mounts. These are used when installing 8.8" shocks on a 7.5" axle housing.

Non Mustang parts below.

K&N panel filters, NIB, $10 each, 1lbs.
33-2024, 3 available, 86-92 Sable/Taurus/Aerostar.

4.0l Ranger extrude honed intake manifolds. $200 for set, 20lbs.
Upper and lower 1993 4.0l V-6 intake manifold set. Both manifolds are new and have been extrude honed to increase the runner volumes and smooth out the airflow. The manifolds are in perfect shape. There is nothing screwed into or mounted in either manifold. They are exactly as purchased from Ford. Part numbers cast into the manifolds are 93TF-9E648-AA (upper) and 90TF-9424-AA (lower).
 
Posted by turbo50 (Member # 6700) on :
 
Welcome to the site.
 
Posted by 65coupe87notch (Member # 9621) on :
 
You should post pictures bro. It will help you sale many of these parts. Good luck! [patriot]
 




Fueled by Ford Mustang Owners
on CaliforniaFords.com