This is topic FS: Complete 75mm intake setup in forum FOR(D) SALE: at Northern California Ford Owners  .


To visit this topic, use this URL:
https://californiafords.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=5;t=077055
Posted by SteveL (Member # 1241) on :
 
I have a 75mm intake setup available.

Accufab 75mm polished throttle body with TPS sensor attached.
Accufab 75mm by 2 inch EGR spacer.
Saleen long runner upper intake with inlet ported to 75mm.
1/2" phenolic manifold space with gaskets. I don't know all the different flavors of lower intake port configurations but the spacer I have is the pattern shown below.

Both the throttle body and spacer have removable idle air blockoff plates which can be removed if needed.
The throttle body and spacer need new gaskets available from Accufab. The ones I have are brittle and should be replaced.
New bolts or double ended threaded studs are needed to attach the throttle body and spacer to the upper intake. You'll probably need longer bolts to attach the upper intake to the lower if the 1/2" spacer is used.
I'll throw in a throttle cable mounting bracket.

I'll also throw in a Ford Racing lower intake but it has been modifed. AN8 rear water crossover was added and the outlets were port matched to TFS High Port heads.

The polished parts are clean. The throttle bracket could use repainting. The upper and lower intakes are cosmetically fair. These parts were used on a 347 w/15psi race motor.

I'll sell the entire package for $225 firm. I would prefer to sell the entire package to someone who needs a complete setup. No 'dibs'. You want it, buy it.

http://www.accufabracing.com/75mm.htm -

[ April 28, 2010, 12:37 PM: Message edited by: SteveL ]
 
Posted by SHORTSHIFTER89 (Member # 7810) on :
 
pm sent
 
Posted by Duncan Motors (Member # 7045) on :
 
intake to?
 
Posted by SteveL (Member # 1241) on :
 
quote:
Originally posted by Duncan Motors:
intake to?
I'm not sure of the question.

In any case, I'll try to get some pictures of the parts today since the rain has stopped then spend some time responding to the PMs.
 
Posted by SteveL (Member # 1241) on :
 
Pictures of the 75mm setup for sale are here:

http://s295.photobucket.com/albums/mm147/1987Foxbody/Parts%20For%20Sale/

To answer some of the questions in the PMs...

I prefer to sell the entire package before splitting it up.
I believe the upper intake is from Saleen but please verify that.
The lower intake is from Ford and the part # is shown.
All these parts were port matched. The port work was done by Lake Speed some years ago.

[ April 29, 2010, 04:51 PM: Message edited by: SteveL ]
 
Posted by M&M Performance *BlownMach1* (Member # 5400) on :
 
ill take it, thanks for the PM. im coming from sacramento so please dont sell it before i get there. thanks
 
Posted by S-trim5.0 (Member # 9899) on :
 
Damn it , u son of a gun !!! I was gonna try n get it but was a lil too far away for me to get there in time .
 
Posted by M&M Performance *BlownMach1* (Member # 5400) on :
 
sold guys sorry!

Thanks steve, good talking with u and good luck in the american iron series, ur car sounds like its gonna do well! see ya saturday!
 
Posted by Duncan Motors (Member # 7045) on :
 
this was the best deal on ca ford history that i have seen in years!!!!!!!! omg!!!!!!
 
Posted by SLPR93 (Member # 8769) on :
 
quote:
Originally posted by Duncan Motors:
this was the best deal on ca ford history that i have seen in years!!!!!!!! omg!!!!!!
yea im still pist off fuck the seller and most of all fuck the buyer [Big Grin]
 
Posted by Stangs R Us (Member # 4495) on :
 
haha ok ok no hating keep it coo here fellas
 




Fueled by Ford Mustang Owners
on CaliforniaFords.com