This is topic 1967 Mustang Drag Race Project / Parts Car in forum FOR(D) SALE: at Northern California Ford Owners  .


To visit this topic, use this URL:
https://californiafords.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=5;t=066566
Posted by lightning89mg (Member # 2673) on :
 
SOLD

[ June 04, 2009, 12:11 PM: Message edited by: lightning89mg ]
 
Posted by tlcluver21 (Member # 9062) on :
 
what else is needed to be done besides the few things you stated for it to be ready to drive?
 
Posted by lightning89mg (Member # 2673) on :
 
To Do:

Wleding - last 2 bars in roll cage, subframe connectors, wheel wells need a small trim and a small bead on each side to close off completely.

Remove Power Steering Arm and Install new manual converter

Mount fuel line (I have all the mounting brackets, was waiting for the subfram connectors to be installed so I could run the line besides the rails)

The rear end yet complete is still a non-posi 8inch. I have the 9 inch housing and complete center, need to get axles and big bearing brakes and install. Or weld the spider gears together in the 8" to make it posi and let ir run until it breaks.

Tune motor.

Install / wire tachometer

Let front springs settle and then cut to appropriate height.

I wanted to add lexan windows, but that is up to the new owner.

Bodywork and lights if wanted. I have all the lights but pulled them to do some body work.

All electrical is good besides what is stated above. Motor and tranny of course in car, shifter installed, driveshaft / drive line all complete, just need to tune the motor and finish above to be good.

Thanks!

[ May 22, 2009, 12:22 PM: Message edited by: lightning89mg ]
 
Posted by lightning89mg (Member # 2673) on :
 
TTT
 
Posted by WickedStang (Member # 7692) on :
 
If it comes down to parting it out pm ASAP! Iam interersted in some things.
 
Posted by lightning89mg (Member # 2673) on :
 
WickedStang, check PMs... TTT
 
Posted by BlowN67 (Member # 4229) on :
 
price on rolling chassis?
 
Posted by lightning89mg (Member # 2673) on :
 
Hi Blown67, i actually dont have a price in mind... Feel free to shoot me an offer but I am actually pretty open and need it out soon.

Thanks!
 
Posted by fasthatch (Member # 7277) on :
 
quote:
Originally posted by BlowN67:
price on rolling chassis?
on roller with fuel system
 
Posted by lightning89mg (Member # 2673) on :
 
check pm
 
Posted by lightning89mg (Member # 2673) on :
 
Pics of the entire car

-

-

-

[ May 24, 2009, 04:29 PM: Message edited by: lightning89mg ]
 
Posted by lightning89mg (Member # 2673) on :
 
TTT
 
Posted by WickedStang (Member # 7692) on :
 
Is it a stock hood?
 
Posted by PeNiNsula302 (Member # 1061) on :
 
ttt [patriot]
 
Posted by lightning89mg (Member # 2673) on :
 
Yes, I have the stock hood... But I dont expect it will suffice if an aircleaner is going to be ran at all...

TTT

Need to sell, price negotiable
 
Posted by 1SLOWLX (Member # 558) on :
 
god damn big enough stall on that bitch...
 
Posted by lightning89mg (Member # 2673) on :
 
Need to get this out.. Price is very negotiable! TTT
 
Posted by lightning89mg (Member # 2673) on :
 
Last time before I part her out... $3800 cash!


TTT
 
Posted by 19mystic96 (Member # 7553) on :
 
part out time????
 
Posted by 19mystic96 (Member # 7553) on :
 
if so, i call dibs on front runners!
 
Posted by SacStangDriver (Member # 8304) on :
 
sold to me
 




Fueled by Ford Mustang Owners
on CaliforniaFords.com