This is topic 1988 Fox Coupe Drag Car Rolling Chassis/Price Drop/Car Must Go!! in forum FOR(D) SALE: at Northern California Ford Owners  .


To visit this topic, use this URL:
https://californiafords.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=5;t=063885
Posted by SVT GI (Member # 8997) on :
 
PRICE DROP $6,000. Added Ebay post.

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MESELX:IT&item=320349482751

Up for sale is my 88 coupe drag car roller. I blew the motor this past weekend at Famoso (fuel solenoid quit w/too much spray, going for 9.0s) Anyway, I'm ready to move on. The car was set up with a BBF and C6 on spray. The car on motor only ran 10.30s-10.40s. The suspension is tuned and it hooks hard. Look at the pics, it pulls the wheels with a 320lb heavier BB and a 80lb heavier tranny. This roller is litteraly a plug and play for a carbed set up, just drop your motor/tranny and go. All fuel and ignition/wiring, guages, cooling, etc are in place right down to just hooking up sending units to gauges. All I'm doing is pulling motor, tranny, drive shaft. This car is 100% NHRA legal to 10.00 with the 8pt, 5 point harness good to Aug 2010, batt box, batt cut off, Axles, wheel studs, driveshaft safety loop, fuel cell, fuel routing, etc. I have all reciepts for the parts listed below. Here it goes:

1988 Mustang coupe (4 cyl)
Paint 3yrs old always garaged, no rust.
New Windshield
Roll Bar- Competition Engineering
RJS 5 point harness
MSD 6 AL
MSD timing control/3 stage retard
MSD Blaster coil
Water pump relay kit for CSR
Griffen Aluminum 2 core radiator
CSR-1 Qt catch can
CSR-3" bottle bracket
DER-Dual electric fan 16"
Holley "RED" fuel pump X 2
All fuel is SS Braided hose
Holly fuel pump 19lb springs X 2
Summit Billet fuel filter X 2
8 gal Fuel cell
Fuel cell mounts
Aerospace drag race front brake kit on SN95 spindles
Earls SS Brake lines
Battle Boxes-bolted and welded
CE weld in sway bar kit
UPR pro series upper and lower control arms (spherical)
Moser 33 spline axles/with c-clip eliminators
Moser 33 spline spool
Custom built 8.8, welded tubes, triangulated
Stange 4.10 gears
Steeda spherical housing bushings
TA Performance housing girdle
Wheel stud kit / Front
QA1 tubular k member w/2 mounting locations
QA1 tubular A-arms
Coil over kit
Lakewood 90/10 struts
Lakewood 50/50 shocks
Moroso drag shocks
Airlift airbags (right rear)
New Spring isolators / rear
Flaming River Steering shaft
Auto Meter Outside mount fuel pressure
Auto Meter Oil pressure
Auto Meter Tranny temp
Auto Meter Water temp
Auto Meter Monster Tach
6" Harwood hood
Weld Draglite 15x3.5 and 15x8 MT ET Drags 28X10.5 w/20 passes.

I know I'm missing stuff, all parts have 20-25 passes on them. This stuff is practically new. You can't build a car like this cheaper. Please no trades, or parting out, I just want to sell. Clear title in hand, $6000 . 805-757-3768. Thanks.

[ March 14, 2009, 07:33 PM: Message edited by: SVT GI ]
 
Posted by svfreerider87 (Member # 5748) on :
 
LOL good luck.
 
Posted by SVT GI (Member # 8997) on :
 
WOW!! So your saying I should GIVE away $9K in parts alone, not to mention the price of the car, paint, and a car that's built right for how much?? How about providing me with a suggested price that YOU think would help us all out.

If anybody else is interested, I am open to serious offers.
 
Posted by Letsrunem (Member # 6305) on :
 
Well worth the money in my opinion. Good luck on the sale its and awesome looking notch
 
Posted by SVT GI (Member # 8997) on :
 
Thanks Letsrunem. Open to offers. I have $13K in the car as it sits w/no engine or tranny. I have a flat bed and will haul if in a reasonable distance. Lets make a deal! TTT
 
Posted by 1SLOWLX (Member # 558) on :
 
good luck on this site... 8500 for a roller in this economy is going to be hard to get. But I hope it happens for you. Nice car by the way
 
Posted by gtowned. (Member # 8156) on :
 
i believe freerider is referring to getting that on this site.not saying that youre asking too much
 
Posted by JohnB (Member # 969) on :
 
It's worth it...but...the economy isn't helping this situation. If you want to get any of that $$$ back right away, part it out. Best of luck to ya.
 
Posted by SVT GI (Member # 8997) on :
 
Thanks guy's, make some offers, you might be surprised.
 
Posted by SVT GI (Member # 8997) on :
 
No one wants a car where all the hard work is done for them?
 
Posted by Casey90GT (Member # 6175) on :
 
PM 1965FALCOON on here...he has been looking for a notch drag car.
 
Posted by SVT GI (Member # 8997) on :
 
TTT
 
Posted by ponystroker (Member # 7635) on :
 
are u flexable with the price at all?

[ March 18, 2009, 09:25 PM: Message edited by: ponystroker ]
 
Posted by SVT GI (Member # 8997) on :
 
What did you have in mind? I have it on Ebay for 8500. There is no kidding 13K in this roller (all receipts on hand). Sinse CA Fords helped me sell my Vert I thought knocking 2500 off for you guys here was good. Something close and we'll make it happen. [Big Grin]
 
Posted by SVT GI (Member # 8997) on :
 
Morning Bump
 
Posted by SVT GI (Member # 8997) on :
 
Make an offer guys. If somebody wants it cheaper without the fuel and electronics, I can work that too. I will not part out the car before hand. The roller must go first. LMK
 




Fueled by Ford Mustang Owners
on CaliforniaFords.com