T O P I C R E V I E W
|
67stang
Member # 549
|
posted
Got my 331 (carbed) dynoed to get a baseline before the S-Trim goes on.
Picked up 10 HP due to very rich A/F ratio
Best run to date before dyno is: 1.54/11.69@119
|
67stang
Member # 549
|
posted
here some movies: http://www.fordmuscle.com/movies/
|
Jeff S
Member # 371
|
posted
Nice numbers! What's the combo?
|
67stang
Member # 549
|
posted
Pretty basic -
Scat 331 kit (JE forged pistons) Stock '90 block World Jr Alum, TEA ported Victor Jr. intake 750cfm Carb Crane cam to my specs (226/230 .552/.562 lift)
10.5:1
|
Jeff S
Member # 371
|
posted
How much boost and what octane gas do you plan to run?
|
67stang
Member # 549
|
posted
quote: Originally posted by Jeff S: How much boost and what octane gas do you plan to run?
Stock S-strim pulley... so 7-8 psi I imagine. Will have to be real conservative with fuel and timing due to the high compression. If I can get away with 91 for street use, that will be great... probably throw in some 110 for track use.
|
2stangs69-91
Member # 1951
|
posted
look into getting a snow boost cooler. With the 50/50 methonal water mix you can run it as hard as you want on pump gass with no det. worries. especialy with your compression. I have one on my 91 and love it. I run 25 degrees total timming. Your car is going to run very hard once you get it dailed in.
|
67stang
Member # 549
|
posted
quote: Originally posted by 2stangs69-91: look into getting a snow boost cooler. With the 50/50 methonal water mix you can run it as hard as you want on pump gass with no det. worries. especialy with your compression. I have one on my 91 and love it. I run 25 degrees total timming. Your car is going to run very hard once you get it dailed in.
yup, i am working on a methanol injection system!
|
F8LPONY
Member # 11
|
posted
Nice #s.
If I was staying N/A I would have to look into my combo a lil better since I am about 10rwhp and about 30rwtq lower than you with a similar sized motor (judging by trap speed I'm about 320-330rwhp). Now i am jeleous hehehe
I am also doing Meth injection for my turbo setup. I don't understand why more people dont do it. Ohh well, let them stay slow while we go fast [ May 10, 2004, 09:42 PM: Message edited by: F8LPONY ]
|
sac 5.0
Member # 2980
|
posted
quote: Originally posted by 67stang: Got my 331 (carbed) dynoed to get a baseline before the S-Trim goes on.
Picked up 10 HP due to very rich A/F ratio
Best run to date before dyno is: 1.54/11.69@119
i have a simular set up as you with a 331 n/a and and sat i was running 12.1 at 116 i wonder if my hp and torque is close to you and if i will be able to get it in the 11's.great numbers
|
Glenn
Member # 520
|
posted
quote: Originally posted by 2stangs69-91: look into getting a snow boost cooler. With the 50/50 methonal water mix you can run it as hard as you want on pump gass with no det. worries. especialy with your compression. I have one on my 91 and love it. I run 25 degrees total timming. Your car is going to run very hard once you get it dailed in.
this might be a dumb question, but how do you determing total timing? If my base timing was at 8*, what would be total timing. Also where can i get that snow boost controler, because it is hot as hell over here.
|
Jeff S
Member # 371
|
posted
quote: Originally posted by Glenn: quote: Originally posted by 2stangs69-91: look into getting a snow boost cooler. With the 50/50 methonal water mix you can run it as hard as you want on pump gass with no det. worries. especialy with your compression. I have one on my 91 and love it. I run 25 degrees total timming. Your car is going to run very hard once you get it dailed in.
this might be a dumb question, but how do you determing total timing? If my base timing was at 8*, what would be total timing. Also where can i get that snow boost controler, because it is hot as hell over here.
Depending on which computer you have the factory cpu adds ~16* of timing at WOT, which would give you about 24* total. If you have a chip then the only way to know is to ask your tuner.
|
FasterDamnit
Member # 442
|
posted
Well, He has a '67 w/ mechanical advance distributer. MSD, I think. So it is prety easy to see how much timing and how fast it comes in.
|
Glenn
Member # 520
|
posted
quote: Originally posted by FasterDamnit: Well, He has a '67 w/ mechanical advance distributer. MSD, I think. So it is prety easy to see how much timing and how fast it comes in.
I have a 95Gt with a stock computer. Now if I bump it up to 10*, will that be too much? The tuner is a little hard to get a hold of now adays. So I am trying to get help from other experienced guys.
|
Jeff S
Member # 371
|
posted
quote: Originally posted by Glenn: quote: Originally posted by FasterDamnit: Well, He has a '67 w/ mechanical advance distributer. MSD, I think. So it is prety easy to see how much timing and how fast it comes in.
I have a 95Gt with a stock computer. Now if I bump it up to 10*, will that be too much? The tuner is a little hard to get a hold of now adays. So I am trying to get help from other experienced guys.
When Byron did your chip was your timing at 8* and did he know that it was at 8*?
You don't need to add any timing to your car that is not the problem with it...unless your balancer is WAY off.
|
Glenn
Member # 520
|
posted
quote: Originally posted by Jeff S: quote: Originally posted by Glenn: quote: Originally posted by FasterDamnit: Well, He has a '67 w/ mechanical advance distributer. MSD, I think. So it is prety easy to see how much timing and how fast it comes in.
I have a 95Gt with a stock computer. Now if I bump it up to 10*, will that be too much? The tuner is a little hard to get a hold of now adays. So I am trying to get help from other experienced guys.
When Byron did your chip was your timing at 8* and did he know that it was at 8*?
You don't need to add any timing to your car that is not the problem with it...unless your balancer is WAY off.
he was the one who set it at 8*.
|